hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi
I'm working on a IoT solution with a small circular board, 26mm in diameter. I was suggested by Johanson to use the 2450AT18D0100 antenna and a lowpass filter designed...
Hi,
I am new to this nrf development, I have been working on the SDK 15.1 on the nrf52832, with softdevice 6.1. I found these examples in the SDK very helpful. I have to...
Hi,
I am planning to send an analog signal to the nrf52840 dongle pin and send it through bluetooth to mobile app. I am thinking of merging ble_app_rscs and saadc together...
The IP mode is IPv4.
1. The hostname resolves to IP address. The resolved IP address is correct (verified with a nslookup command separately).
2. setsockopt(fd, SOL_TLS...
I am implementing a serial transmitter using the nrf_serial library from the nRF5 SDK 15.3.0. The application is very similar to a serially addressable LED string.
My serial...
Hi,
i m using my custom nrf52832 beacon.For Battery power, i used accelerometer.i trying to change advertising interval for non connectable BLE device while accelerometer...
Now there is a project, nrf52840 uses SPI to communicate with other microcontrollers. Data is currently available, but it is suspected that each packet lacks a second byte...
Using the nRF52832 device with the S132-v3.0 soft-device (s132_nrf52_3.0.0_softdevice) and SDK version 12 (SDK120200F12) (Customized for our application, which includes use...
I am working on a ble nus pheripheral application on nrf52810 with sdk 15.2 and s112. currently I can connect to nrf52 with 4 mobile phone at same time and send&receive string...
I managed to set the UUID section on my own, but I'm having trouble reading and writing some data. I'm changing the on_write function in Ble_nus.c, but I can't get results...
Hello,
When debugging one of the projects, I encountered the situation of a frequent reset of the device during connection. A quick scan under the debugger helped show the...
Hello,
I'd like to develop and base on the " Experimental: ATT_MTU Throughput Example" project.
Seems like the example project doesn't implement the DFU (aka, OAD).
...
Hi Nordic,
In my custom board, I need to access peer data at quite early stage - to determine which board it is.
So my question is: Can I call pm_init() (in peer_manager_init...
I have a scanning application that uses pc-ble-driver-py to communicate to the nRF52480 Dongle on Windows 10. I'm using connectivity_4.1.1_usb_with_s132_5.1.0.hex in the dongle...
Hello,
Does nRF905 communicate underground? I mean if I bury one chip underground would it be able to transmit to a receiver on the ground?
If yes, How deep could the...
