hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hello,
I have an application that advertise specific data. Data is long enough that I cannot fit my 128bit service UUID. I think of 3 options:
1. Use my service UUID but...
Whenever I store my data in Flash using FDS (Flash Data Storage Library) it stores a random value (but fixed) even though I am giving it a value.
I run the same thing in...
Hi, As the title states when I try to add characteristic to my custom service the function returns error 16. I have set NRF_SDH_BLE_VS_UUID_COUNT and adjusted the linker accordingly...
Good day,
I am starting a new project where I am using the ANNA-B112 BLE device from ublox in a custom design. The ANNA-B112 interfaces with a host MCU over UART. I would...
Hi,
I have added nus service to the relay central and peripheral example.The relay board advertises and i can connect to the peripheral part of device through the nrf connect...
The mesh health model state is not restored following a reboot in the current version of the Mesh SDK using the light switch example.
According to the documentation, the...
Hello folks, I am new to Thingy 52 PCA 20020 model and I have downloaded nRF SDK 15.2 and I am using a Segger J-Link programmer/debugger. The thing is I would like to get...
In acces.h there is the publish period format definition, which is
/** * Model publish period structure. */ typedef struct { /** Step resolution. */ uint8_t step_res : ACCESS_PUBLISH_STEP_RES_BITS;...
Hello,
I was surprised that gcc did not optimized my strlen("FOO") construct (worse, in a code review, I argued that the compiler would do the optimization…)
It seems...
Hey there,
I am trying to develop with the Bluetooth Mesh SDK for NRF5.
We have two chips, NRF52840 and NRF52840/NRF52832and are using the light_switch example from the...
I need to save energy for my ble application. So I turned off the sensor when there was no ble connection. A ble connection is a condition for me to turn on the sensor, but...
How exactly are the UART pins selected for the nRF9160? I've searched and am unable to find a file to configure pins. I need to change to pins from the development board to...
Hi,
I'm working with the SAADC on an NRF52832. I'm using the SAADC driver from SDK15.2.
I have a problem with the calibration routine because it's generating DONE events...
