When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello,
I have a device that advertises as `BLE_GAP_ADV_TYPE_CONNECTABLE_SCANNABLE_UNDIRECTED`. When a device connects, it restarts its advertising as `BLE_GAP_ADV_TYPE_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
Hi,
i have developed a Windows based App in Qt that using BLE.
My problem is upgrading a remote device Firmware using BLE.
Did exists any type of C++ class automator...
Hi Nordic!
I faced a problem when I want wake the MCU up from SystemOFF.
When my nRF51822 is in SystemOFF mode, a watchdog chip wakes up the MCU. After sending the...
Hi.
I think i just fried my NRF52840 dongle. VDD out is only about 0.5V :| I'm currently powering it from the usb port (VBUS is correctly +5v). Could it be that Ii only...
Hi,
I"ve designed a custom board with the MDBT50Q module (part of the schematic below). When writing my program to Flash 0 and Ram Memory 2000 0000, the program won't load...
I have been experimenting with the example of the MQTT Client Subscriber/Publisher from de nRF SDK. I use:
SDK v15.3.0 (also nRF5 SDK v15.2.0).
Raspberry Pi 3 (as a...
Are there any working projects that integrate TWI and MPU6050 sensor. That are edited by KIELu5 and follow the SDK 15.3v ? I tried modifying the 'twi_sensor' project but I...
Good day
Im trying to switch off an LED when my relay/hopper is not advertising. I switch the LED on successfully when transmission starts but I'm struggling to do the sd_ble_gap_adv_stop...
Hi, everyone,
now I'm test " \ncs\nrf\samples\nrf9160\gps\build_nrf9160_pca10090 ",
it's error about" nrf_socket.h: No such file or directory"
I'm find the file at ...
So this is a small continuation of this ticket https://devzone.nordicsemi.com/f/nordic-q-a/50656/using-pdm-mic-on-nrf9160dk .
The problem I'm having now is that when I run...
I wrote UART echo sample based on ble_app_uart_c for S140/ nRF52840-DK.
When nRF52 receive one line on USB/UART, it send same line to USB/UART.
I also write Linux socket...
I am following this tutorial:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/application-timer-tutorial?CommentId=43347679-22d9...
Hello,
I want to use the ADC for a burst @ 8khz.
I use this sample " test_adc_sample_with_interval " from https://github.com/zephyrproject-rtos/zephyr/blob/master/tests...
Greetings...
Please help me understand why PB-GATT support is removed from SDK UART coexistence example?
The dilemma I am facing is as follows:
1. No PB-GATT for SDK...
