Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
I am trying to get the "ble_connectivity" project to work on the nRF52840 Dongle.
I am using a nRF52840 DK as a debugger, and SES Nordic Edition V4.16 (64-bit), with SDK...
Hi,
I received the nrf52 DK I ordered before, but I just realized that I can't find the schematic document for it online. Is it private?
Can anyone help? Appreciated....
When trying to import a project as ber the getting started assistant I get a "Can't Load Project File" error in SES with the below log. Does anyone know what the source of...
Hi, I want to try to connect a Samsung Galaxy S5 Neo (Android 6.0.1) with nRFConnect App with the HeartRateService example. The HRS runs on a nRF52840 Preview DK with SDK14...
nrfutil 5.2.0: init_packet missing from manifest.json. Checked the generated .zip using "nrfutil pkg display", the data are in .DAT file for each image. Does that mean our...
Hi,
We are developing sensors with the nRF52840. We send data packets of approx. 160 bytes with 25 Hz. We interact with a PC (Ubuntu - bluez 5.48) which works with one sensor...
We are using a Nordic 100028 usb dongle programmed as a ble uart central to interface with our ble uart peripheral based boards. The subject line pretty much says it all....
Hi,
I'm trying to flash the asset_tracker application to the nrf9160dk. I use Segger Embedded Studio for building the project for the nrf9160_pca10090ns board. However,...
Hi,
We are using a NRF52840 chip (SDK 15.3) in an application where we use the softdevice (S140) in combination with 2 UARTS: one for sending out debug output (UART0 - nrfx_uart...
Hi, We have a nrf52 which runs some project using ANT, now we would like to implement BLE for UART communication between a phone and the unit. The code base is already extensive...
Hi,
I just connected an nRF91 dk to nRF Cloud, which worked fine. However, for some reason the GPS says I am in Trondheim, while I am clearly somewhere else in the world...
I try to communicate with NRF52832 with NRF51822 for the example radio receiver and works well with SDK5 12 3
when I try to communicate with E73 (NRF52840) board(E73(2G4M08S1C...
How to push Initiator to resolve its private address (seen at direct_addr of adv_report) when bonded private Advertiser does a direct advertising?
I need the only Initiator...
I've followed the procedure on the nRF connect cloud to verify the SIM card and add the LTE device, only once the LED3 and LED4 blink at the same time like it was connected...
