Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I've worked with other integrated radio + ARM processors that were not deterministic, and I would like to know if the Nordic solution is.
What I mean is: Is there a way...
Hello all,
How does the handling of ble events work with SDK 15.1? When I register more than one event handler with the macro NRF_SDH_BLE_OBSERVER(), how does the softdevice...
Hello Support team,
I'm working on a project where I am designing a custom board uisng the Nordic NRF52840 as the MCU (forgive me if I'm using the incorrect terminology...
Hi,
I am relatively new to programming hardware at this level, and have developed our product on the 52832, so finally I have purchased the Power Profiler Kit, and downloaded...
Hello good morning,
I am using nrf52840 device. I am sending 20 bytes using notification at different notification intervals like 30ms, 80ms and 1sec. But at application...
hello
I am currently trying to use the thingy_52_sdk sample code to embed a program using the J-link debugger with the Nordic thingy 52 development kit. But the build is...
Hello,
I am attempting to test slew of Rigado BMD-350 module BLE radios (uses nRF52832) using a Rigado BMD-301 series Eval Kit to act as the central. The BMD-350 device...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132. In the ble_peripheral / ble_app_uart example you can only connect through the...
If followed the following steps:
Installed Win10Pcap
Installed Wireshark-win64-2.63 on Windows 10.
Using nrfGo Studio loaded sniffer_pca10040_51296aa.hex (after erasing...
Hello fellow Nordic Community,
We have a usecase in which it would be beneficial with a tx power of - 30 dBm . This is a value that was supported with the nRF51 chip series...
Hi,
I am develop a project with dfu and bond features. I found that in dfu project, IS_SRVC_CHANGED_CHARACT_PRESENT is always set to 1. In my understanding, if set this to...
hi,
i am using Nordic thingy:52 with a nRF52840 with s140 softdevice to receive multiple characteristic data from thingy like thingy environment service have 6 characteristics...
Hi,
Is there any way to stop the OTA DFU? Let's say that I started it and at some point I want to cancel the process at 40%. Is there any way to send a control message to...
Hello fellow developers need your help
I have bought 3 nRF52840 dongles and want to setup a mesh network as stated above. I have downloaded nRF Connect windows application...
From this ( https://devzone.nordicsemi.com/b/blog/posts/measuring-lithium-battery-voltage-with-nrf51 ), there is capacitor connected to adc input pin.
But is it necessary...
