Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
I am using nrf52832 to develop based on SDK14.2. I have defined a custom service . There are 7 characteristic in this service. The attribute of each characteristic is set...
When broadcasting mesh messages I use the access_reliable_t struct to set data.
I need clarification on what the contents indicate. The documentation is sparse and doesn...
I'm trying to model up current consumption of our system. I'm looking to put the nRF52840 into System OFF, no RAM, Normal voltage mode and waking up on both GPIO and USB Detect...
Hi,
Is there a list of the exact part numbers for all the components used in the nRF52832 reference designs? I could only find a pretty general Bill of Materials in the...
I am planning to make a custom board using nrf52832 ,for that i need to know what are all the steps need to be followed to perform OTA DFU to upload a custom firmware . List...
Hi everyone.
I'm working with light switch example in MESH SDK 2.0.1.
I want to provisioner working like a client. Provisioner can send command to another node to on/off...
I have to implement temperature sensor readings continuously through interrupts instead of busy waiting example in SDK in order to notify those values over BLE to cloud. ...
I'm looking to encode and decode an AFSK signal (via wire not RF) using 2KHz (0) & 4KHz (1) with an 8-bit frame size and 6 frames to a block. Is this achievable with the Micro...
hello sir i am designing a custom pcb based on your mcu nrf52832 board
can you help me how to customize it according to my need without disturbing antenna .
USB device don't recognized by system if we try to use more than one endpoint in app_usbd_hid_generic library:
APP_USBD_HID_GENERIC_GLOBAL_DEF(m_app_hid, INTERFACE_NUMBER...
Hello Nordic
I'm using nRF5_SDK_15.0.0_a53641a.
I think I found a bug with the ble_nus.c, line: 96
I think the rx_handles.cccd_handle should be the tx_handles.cccd_handle...
Dear all,
I'm trying to run nimble stack with Nuttx OS on nrf52832(pca10040) reference board. Now , most function is working , but it is not stable .
Sometime , the svc...
Hi,
This function is called after I turn on Bluetooth a while of my project.
What is the cause of this and How can I do to fix it? I can't debug to source code of softdevice...
Hi, We used Nordic SDK12.2 Softdevice3.1 to develop our smartwatch. After launching our product, we got a lot of complains on the connection and re-connection on Samsung Android...
