Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi!
I have some troubles with making embedded serial port working on NRF52-DK. Basically I can receive data sent by nrf chip but I cant write. When I write something using...
More of a suggestion than a question:
Using the info available on the infoCenter, especially here and here , I'm trying to implement a way to dynamically select the DFU...
I use Adafruit Bluefruit library and developing code to run on Fanstell BT832.
Up to know i have been able to compile several examples and run it on the NRF52 DK board....
Hello! I am new to the Nordic and Bluefruit enviroments.
I am currently working on getting a scan response request from the scanner to the advertiser and have the advertiser...
Hello devzone,
There are 3 {37,28,29} channels for advertisement & i want to advertise only on 37.
Soft: Nordic mesh v1.0.0 stack & pca10040 nrf board, light switch example...
Hi, I'm trying to controll the port of my nRF52832 by writing to a characteristic value. So far everything works fine but I'm unable to get the value of my characteristic...
Hi all,
i development a FW with a low power and when i measure the power consumption using a nrf connector on evaluation board i have 2 ua, and it's ok. Now i have the some...
So I can see the "API Reference" documentation on the UART driver in the info centre, however this is all very low level and I am going to waste hours going through all this...
Are there any changes required to run the Sample Bluetooth Low Energy (BLE) applications from nRF5 SDK v14.2 when migrating from nRF52840 IC Rev A to Rev B? I have followed...
Hi,
I am using the nRF52832 on a custom PCB and I am interfacing it with a flash memory chip through SPI.
I am testing the SPI communication using the spi example (nRF52...
Dear Sir,
1. The HFXO crystal can be with load capacitance 12pF? or 8pF is better?
2. According to the datasheet, "17.1.1 64 MHz crystal oscillator (HFXO)"
there is...
Hello,
we have two custom boards with nRF51822.
We use NUS.
If our pakets under 23 Bytes everthing is fine ....
If we want to sent paket with 140bytes, the central...
Hi!,
I've made a custom board using Taiyo EYSGCNZWY bluetooth module, to be used as central in a project. To use this module, several changes have to be made in the clock...
Hi,
I am using nrf52840 to verify a signature using RSA and cryptocell c310.
I get error 0x07 when I try SaSi_LibInit();
My rndContext and the buffer are both declared...
