Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I have taken a look the APIs which the S132 supports in nRF52 DK.
However i could not find the APIs that can initiate the channel map update ,feature exchange & version exchange...
hai
i have this code to save and read some data in flash.but the stored and read data are not same. always reads zeros. how can i solve that.........?
here is my code...
I'd like to be able to quickly update the advertising data using
sd_ble_gap_adv_data_set()
and at the moment I'm doing this via a bit of a hack, as I captured the advertising...
Normally, Raw data has TYPE (0x01), TYPE (0x09): device-name, TYPE (0X07): UUID 128 bits.
However, there are devices without TYPE (0x07).
Is this also a problem?
Communication...
Considering using an nRF52 module, I'm developing using EvoThings' native plugins right now. I don't think we have the resources to do IOS and Android native apps.
Has...
I have an application where my nrf52832 acts as a peripheral and I can connect to it without problems, but after some time like aprox 10 minutes when I try to connect to it...
Hi!
I have searched for this questoin, but not found anything useful. Probably I an not using a good search phrase.
How do I determine how much space is left on a nRF51...
This is a general question I will throw out initially, but I can get more specific if necessary. This is something I see a lot in my year or so of development with nordic...
SDK:8.1.0
Chip:51822AAHO
Hi,i use the nRF51822-PSV3.1 Schematic diagram.The chip set 4dbm tx power,
then i test the test point(C6) as follow,2402MHZ and 2426 MHZmax...
Hi,
I run the HID keyboad example, and a problem confuses me. I use the "lightblue" APP to connect the peripheral--"Nordic Keyboard", but the iphone appears a pairing box...
Hello!
I have been working recently with the PCA20006 Beacon board. The example we have tested is the ble_app_beacon that allow us to change the UUID/Major/Minor and go...
This may be a stupid question, but...
What value is BLE_GATTS_ATTR_LENS_MAX
Its mentioned a lot in the SDK, but I can't actually find a value for it actually defined...
I would like to know how to add Service Change UUID: 0x2A05 Properties: INDICATE Descriptors Client Characteristic Config UUID: 0x2902 to Generic Attribute of Nordic_HRM....
