Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Currently I have a few characteristics which are Authorized Read and Writes. Upon detected of the Authorization from the Central I trigger a few events such as:
Measure...
Hi !
I'm using an nRF52 on PCA10040 board and nRF5_SDK_11.0.0_89a8197. I want to run the peripheral ble_app_template with SEGGER Embedded Studio v2.20. I correctly set...
In an effort to try and determine why FreeRTOS tickles idle is consuming more current than tick mode with an idle task, see this post devzone.nordicsemi.com/.../ , I noticed...
Hi, i am designing a board using nrf51822 and planning to use a MOSFET for reverse battery protection instead of a schottky diode or a normal diode. I am new to this and learning...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I'm developing a nRF52 application that exploits two ADC channels in single ended configuration.
VDD is 3.0V.
For the signal conditioning I've chosen a driving Op...
I've been trying to get my head around using a BLE central and making connections so I've loaded up the multi-central example to figure out just how everything works. I turned...
Hi everybody!
I am working with ANCS (nrf51822 SDK 9.0) I am confusing on setting the connection parameters which are MIN an MAX connection interval.
Firstly, I set...
Hello,
I have some characteristics on my device that are containing some configuration data.
Every single variable is a global variable.
The values can also be changed...
I am using the nRF51822 bluetooth low energy smart beacon kit and am running into trouble using the GPIOs available on the board (pins 0, 1, 2, 3, 5, 9, 11, 20, 21, 24). For...
Hello Everyone,
I am trying to monitor my battery voltage on the analog pin (ADC) so inorder to do that i am going to use the voltage divider circuit to calcualte the R1...
Hi,
We are working on a smart lock project with nrf51822 third party module with an antenna on pcb.
We are trying to cover 50 cm range at -20 dbm. But even at -30 dbm...
I have created a library for HD44780 Hitachi LCD, and I can transmit data to the LCD through an IO Expander without any problem over TWI lines. Right now I am not using any...
