Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hi,
I am developing a product for the 433MHz band. Due to the space constraints I had cut the ground plane to very small and also had to rearrange the components away from...
Hello everyone,
This image was copy from "infocenter.nordicsemi.com".
I'm trying nRF51-DK (IoT SDK) with Coap server , (raspberry pi with Coap client by python example...
Hi,
we are using RTC2 with APP_IRQ_PRIORITY_LOWEST. But the code hanged inside the interrupt handler. when we did step through debug, we came to know that in nrf_drv_common...
In nrf52_SDK/examples/peripherals/rtc we tried adding the UART prints and verified. It was working fine for RTC0 but fails to do for RTC1. Could you please give any hint on...
Hello together..
i have a problem with the nRF51 DK.
I tried a little bit with this DEVkit i.e. copy the blinky example to the JLINK storage.
This works fine.
Regarding...
Hello,
I am developing a new product using S130 on nRF51822(QFAC). My product use LCD as spi interface and ADXL345 sensor as i2c interface, also test it, works well without...
Hi all:
To saving power I implement the function to read data after interrupt is triggered..
below are my codes..
My expectation is..
Let CPU enter idle mode to wait...
I am trying to set up a GPIO interrupt, and found that whenever Button 1 is pressed, if Button 1 or 2 is pressed later, the app will reset. This is even if there is any other...
Hi.
I want to make a device which can connect each others and communicate with NUS.
I need not to use any other service without NUS.
I made nus_c service which is a central...
Hi
I can't seem to find this in the datasheets, what is the active current consumption of the nRF52832 chip, I'm interested in the maximum expected current consumption...
Hi!
I want to connect a nrf51 dk with a beacon and I'm using the UUID to make the connection. In the beacon code I define the UUID in this way:
ble_uuid_t adv_uuids...
I use nrf52832 with softdevice s132_nrf52_1.0.0-3.alpha for a ble application on own pcb.
first I'm not sur of adresse to use for iROM and iRAM areas. I've this parameters...
//Hi Everyone!
//I am programming a nRF52832 through the SDW interface and am having trouble answering some questions.
//So, first off is simply checking my understanding...
I have a recent dev board and am using SDK11 with gcc.
I can build and flash OK
The blinky sketch runs
However, when I load up examples/ble_peripheral/ble_app_proximity...
We bought the Beacon Kit from Nordic. I'm trying to use the firmware code on a similiar beacon board based on same Nordic Nrf51822. The board has same button and led pins...
