Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
hi, guys.
I'm prepareing the Korea certification, KC, with nRF51822 BLE system.
I'm progressing to get KC by certification agency.
Today, They will have RF signal test...
I was comparing the binaries for the S120 and S110 stacks and see the MBR is different.
I was under the impression that the MBR never changes and was thus expecting it...
Hi Nordic
We want to test radio parameter through IQxel . Now,we need a application software to control nrf51822(TX,TX,outpower,channal and so on ) . Can you recommend...
I'm using the example code for simple device/host Gazell in SDK 7.1.0 as my starting point for my application.
My program runs for a second or two, then ends up in the...
Hi
I am new to programing low energy devices. I got a Blend Micro from RedBearLabs. I am using the
nRF Master Control on android to connect to it. I am able to change...
As I create my first 'profile document', it would be nice to read over some examples. My only knowledge of this document comes from nAN-36, section 2.2.2.5 :
A profile...
Hi
in the SDK 7.1 examples, there are examples about how to use the hardware peripherals, and examples on how to use the BTLE stack, but nothing combined.
How do I combine...
Hello, I've started bluetooth development with nRF51 DK since yesterday.
My devlopment platform is KEIL-MDK(v5)
Yesterday, I just tested my board, download the blink...
I have an nrf51 dev board which i can currently connect to an android phone and read data from. I would like this board to be able to scan for other BLE devices and send data...
While attempting to understand why my S120 v 1.0.1 application aborted in:
sd_softdevice_enable(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, assertion_handler);
producing:
ASSERT...
In regard to the following functions
uint32_t sd_nvic_critical_region_enter ( uint8_t * p_is_nested_critical_region )
uint32_t sd_nvic_critical_region_exit ( uint8_t...
Hello, from looking at the GCC linker files I take it that S120 softdevice doesn't support using the full 32KB RAM of the new nrf51422-xxac devices. Is this something that...
Hi, I have written a simple program to calculate the number of retries with nRF24L01+.
On transmitter side, maximum number of allowed retries is set at 1. The transmitter...
Hi all,
I am a beginner with nRF24LE1, when I want to code some examples using GPIOs, I find that it's difficult to understand the PxCON register function. Whether I configure...
I am using the usb port to download an example project to the NRF development kit board, with Keil4. Somehow it keep telling that "No jlink device found", in Keil, the project...
