Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
Uint32_t data using sd_flash_write written many times to the same address, you must perform sd_flash_page_erase before writing it?
(English is not good, with Google Translate...
Is the DC/DC converter enabled when running ble_app_beacon?
Or is it only the LDO that is enabled?
I am running the application on nRF51822-DK.
BR Magnus
Hi,
I happily use the JLINK UART interface which show up as COMxx on windows for both the PCA10000 and PCA10001.
We are trying to 'see' the same on Linux. Have inatlled...
Could you please let me know the current rating in between retries while transmitting.From the oscilloscope reading, that is not obvious. The documentation shows three idle...
Hi
We had some problems updating our devices with the nRF Loader App on IOS. After selecting the device in DFU mode the App hangs and aborts with a Bluetooth error after...
Has anyone been able to get the DFU over the air bootloader to work with gcc and the newest SDK (6.0)?
I have followed all the tips I can find on here to get it working...
I'm wondering if the timeslot API is planned for the s130 or if it's intended to be s110 only. If it is eventually getting added to the s130 is there a loose time frame for...
Hello,
i am using the nrf51822 with softdevice s110. In the spec i read that the contoller works as well with an external 32khz reference which i want to use. The oszillator...
hello everyone,
i use nrf51822 and i want to use one switch that wakeup the module from sleep mode. so can i connect switch to gpio of nrf51822 module. if yes than which...
I'm a newbie so bare with me. I had this code running, saved it, and started another project. I tried not to touch any of the files I had running with the example below, but...
application note nAN-034 describes two alternatives for production testing an application using the nRF51822. One method is using a commercial tester (MT8852) and the other...
I need to send data PIR motion detector sensor to the master controller in my motion detector network.
Can I get away with just one of the nrf51 chips and my PIR sensor...
We're trying to decide at what voltage we should run our nRF51822 on the next revision of our board. To date we've been doing fine at 1.8V. The current drawn on a 3.7V lithium...
hi, i made ble app including bootloader using nRF51822 (s110), sdk 6.1.0
when i use sd_nvic_SystemReset() function in app, it erase app's pstorage.
But i want to preserve...
Hi,
I use S120 as central device and I need to handle multiple connections.
However S120 works quite unclear to me.
If S120 doesn't reply to BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST...
