Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
Hello:
When I use Android 4.3 to connect nRf51822 AKII board, HEART RATE always show error on discovering services(129, then I can't connect nRf51822 AKII board.
Does...
Hello,
i want to develop open source software for nRF51 but i think the SDK licensing is to restrictive. I cannot use any of provided example code because its permits redistribution...
This is my code snippet
int main(void)
{
uint32_t err_code;
...
// Scheduler
scheduler_init();
// Initialize the SoftDevice handler module.
SOFTDEVICE_HANDLER_INIT...
Hello,
I was working over nordic dev board and found the uart template. but in that, only "data_receive_handler" is mentioned. i want to send data from my dev board to...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC RTC.
It function well when connected to EV board...
I see the "Emulated System OFF...
Hi all,
I'm using the nRF51822-EK (PCA10001) and I'm going to develop a bluetooth cadence (and speed) sensor for MTBs.
I desire low power consumption and i though to put...
hiii...
I was working on ble_app_hrs example of sdk-6 using sd7.0.0. I tried to add broadcast feature by sending some hex values, dat was working, but now i want to display...
Hi,
I need to use 2 TWI bus (hardware constraint) so I wish to drive one bus with twi_hw_master.c and an other with twi_sw_master.c.
Each bus have their own GPIO.
...
Hello.
I'm reading the nrf51 Reference Manual.
in MPU section, [ (SWD) will no longer have access to code region 0 or code region 1, as well as no longer being able to...
Hello,
downloading the file nrfgo_sdk_2.3.0_setup.exe causes the virus scanner to report an issue and moving the file into a restricted zone.
Can you help on this...
hi, i made ble app with nRF51822 (s110), sdk 6.1.0
and i put this code after a pstorage_store() function to wait finishing of this function.
uint32_t err_code, count;...
My board is nrf51822.
Simple_uart works fine in uart_example, but once I copy it to my ble project which can work, it stuck.
Part of my code :
advertising_init();
services_init...
Hi all,
Now I'm using the nRF51822 DK and nRF Loader APP do the OTA.I can use the APP to complete the firmware update.However,the device
cann't go back to bootloader mode...
I'm trying to build an application on nrf51422 with s310 SDK ver5.2. My application is working fine with Bluetooth and now I want to add ANT service to it so can anyone please...
We are running OTA DFU bootloader provided in SDK 6.0 on nrf51822. We noticed that when the chip has been on for a while and we quickly power cycle it, the bootloader sometimes...
