Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi there,
I want to use a LiFePO4 Cell to supply the nRF9160:
Is the MAX17224 suitable to power the nRF9160?
Is this Power "Sequence" OK? Productspecification nRF9160...
currently we are facing an issue with our testing that, our product battery is getting drained to 0 volts. we understand that we need to put a cutoff voltage from the firmware...
Hey folks,
I'm developing a long-range application with nRF52840 DK that (optionally) uses NUS (Nordic UART Service) to send data to Samsung S10+; there is no problem establishing...
Hello,
SDK 15.3.0
nRF52840-DK
s140
IDE:SES
I am running into an issue using the app timer and LPComp together. The error is NRF_FAULT_ID_SDK_ERROR, With RTT output...
Let say during the normal program flow I want to change often the edge direction which will trigger the event: rising edge, none, falling edge, none … Can I work direct with...
hi:
i want to know CKCON config is CKCON =0x01 or CKCON =0x02? because datasheet is CKCON =0x01
External data memory stretch control. 001: One stretch cycle (default)...
Hi All,
I'm working with Nordic BLE Mesh and trying DFU (OTA) provided in sdk for Mesh.
I used \doc\getting_started\dfu_quick_start.md as the guide to setup and test...
Hello,
I am using nRF52840. I am trying to get hands on DFU. Without any modifications, I am using examples as is.
1) I followed below steps to do DFU hrs_application_s140...
I am looking for some 'getting started' information on configuring the nrf52833 DK for direction finding.
I have read the thread: https://devzone.nordicsemi.com/f/nordic...
Hello,
I have made a custom board based on NRF52840 IC.
The board is using GPIOTE, SPI2 and TWI1, and when put to sleep, consume 665µA. When just initializing the SPI...
Hi,
I would like to read accelerometer value from orientation_detector_calibrate() (in asset_tracker/src/orientation_detector/orientation_detector. c).
But from main.c...
Hi,
I am learning nRF development with 52DK device and SDK v16.0. I noticed that by default the 52DK planned P0.5~8 for UART purpose.
I am wondering if I can disable UART...
Hello ,
I am trying to send 1,000 of MPU-9250 data from NRF5832 peripheral(ble_nus_uart) to NRF52832 central(ble_app_uart_c).
And i have been searched this site and set...
I would like to move existing nRF9160 solution created according to nrfConnect Getting Started Guide to another directory under Windows.
Simply moving the folder doesn't...
