I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
When using the script interactive_pyaci.py together with ipython and the serial example, I observe a strange formatting in the command window, because the "In [..]" is often...
SDK is nRF5_SDK_13.1.0_7ca7556.
Example is ble_ant_app_hrm.
Softdevice is S332.
The example can connect android but can not connect iphone.
Iphone 7 and ios is 10...
Disconnection of the peripheral is done without enabling another connection, the only way is to reset the module.
It happens sometimes after 5 min up to 1-2 hours.
If...
Hi all,
I'm working on an application that requires BLE. I've recently upgraded my project from sdk 14.0 to 15.2 in order to deal with some problems that I ran into with...
Hi,
I am trying to configure the nRF52810 clock setup to accept the LF CLK source from a pin on stm32l4xx on a custom board without much luck. My setup works correctly if...
Hello. I move ble_app_uart with a combination of nRF 52840-DK and SDK v 15.2.0. Using UART 0 or UARTE 0 confirms that it can communicate with nRF 52832 on the Central side...
Hi,
I am trying to understand the current consumption of a very simple BLE application running on the nRF52832 DK. For my final use case, I'd like to reduce the peak current...
Our project uses a Raspberry Pi compute module 3 connected via UART to 2 nRF51822. I'll go through what is working and than describe the issues I'm having
What's going...
Hi, I'm using ble_app_hrs_freertos from SDK 15.2 on PCA10056. I noticed that logs stop working (RTT) when I increase configTOTAL_HEAP_SIZE to 64k. I tried play with various...
I've got myself one an E73-2G4M04S1A board containing an nRF52810 chip for evaluation. I've setup an Raspberry Pi 1 rev2.0 with OpenOCD using this guide and wired it up according...
Hello,
i have bought 3 modules from Rigado (BMD-330-A-R) with a nRF52810 SoC, is it possible to flash it with an Raspberry Pi? I read that SWD is possible by its SPI-Interface...
We are in progrees of developing a wearable device using NRF52832 with BLE. The problem is, we have quite a few chips dead after several times of rewriting. The dead chips...
Hi,
I tried adding PWM for turning on/off the LED's on the DK for the Enocean switch example. It worked well.
I tried to perform dimming on the switch example by restricting...
Hello All,
This is a trivial question I guess but I am not able to figure out
Working on : nRF5 SDK for Mesh v2.2.0
SDK version : nRF5_SDK_15.0.0_a53641a
I have...
