Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
HI I have build the hex but it is not working it didn't provisioned using provision example in sdk2.2 and I noticed no led light up on device reset. Is it due to soft device...
Dear Sir,
I am trying to implement the following scenario. I am working on nrf52832 with SDK15 and soft device 6.0.0.
I have a peipheral device which is advertising for...
ruuvi is connected to ruuvi dev board to Nordic dev board connected to Mac book pro.
As usual
But
nrfjprog version: 9.7.3
JLinkARM.dll version: 6.33a
...
I am using Nrf52 DK as a J link programmer to program Laird BL-652 which is connected to NXP LPC 1519 via RX/TX Pins. I am trying to send commands from BL652 to NXP via UART...
Does anybody develop bluetooth JOYSTICK?
Could you please help me with some code samples to understand how to do Joystick on NRF products.
Best regards.
Hi
I am setting an interrupt off the RTC to cause wakeup from nrf_pwr_mgmt_run(); This is to conserve power. My code is working but the times are out by an order of magnitude...
Hello,
Will there be a migration guide posted for v15.1.0?
What is the suggest path of upgrading from v15.0.0 to v15.1.0?
Is it generally suggested to upgrade to new...
Hello,
I have not seen any mention of a BlueZ based BLE DFU library other than here , which was a long time ago.
I will require this library for my current project so...
Hi team,
My customer needs to make some adjustment on I2C frequency due to their SW requirement. As our reference on datasheet, I2C frequency needs to be 100kbps, 250kbps...
Hey, i want change the simple_on_off model a little bit, so the server return an byte array to the client get_message, can you say me how to include vendor specific model...
If nrf_gzll_ok_to_add_packet_to_tx_fifo() returns false and nrf_gzll_get_error_code() returns nothing, what does this mean?
Facing this a lot when trying to change channels...
Hello,
I was trying to perform DFU over mesh. My setup was as followings:
7 nrf52832 Devies. One of them is connected to my laptop.
I programmed those according to this...
Hello,
I'm using the nRF51422 with a dfu dual bank bootloader with SDK 11. I can programm the uController with the Softdevice and the bootloader and afterwards load successfully...
Hello, I'm trying to add a Peer Manager functionality to the Mesh Provisioner application.
I'm using nRF52832 devkit, Segger Embedded Studio, nRF5 SDK for Mesh 2.0.0 and...
