Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello Pros,
I maybe running the nRF52 close to its limit. It appears to have a probability of 1/1000 to 1/2000 to hit a 3004 in a continuous time-gated packets stream....
Hi,
I have created a custom service, and now I want to add different characteristics to it but with completely different uuids, not only the 12-13 octets.
This service...
Hello All,
I am working on nrf51dk , we are facing the issue if we send > 8 bytes of data in one time from Uart console then BLE_NUS will reset..
Our Setup:
ECU --...
Hi, around July Nordic Semiconductor released this SDK which featured examples of BLE mesh that uses a dev board as provisioner.
This program is OK, but it has zero possibility...
Hello
Recently I bought two PCA10056 boards in order to explore USB capabilities of new nordic chips. I've tried usb device examples supplied with SDK v14.1 and v13.1 on...
Hello All,
we want to calculate the total power consumption when the controller is put on SYSTEM ON low power mode. Do you have any information on the way to do this? ...
My Central is willing to perform a bond ( pairing with bond ) to a Peripheral.
As an example and according to
Message Sequence Chart > Central Security Procedures >...
I have some copy jlink, they can used in keil and JFlash.exe, but can not use in nRFgoStudio.exe, is it right? nRFgoStudio can not support copy jlink edition?
Hi,
i have a wierd behavior on my board.
On my nrf52832 custom board i have sdk14.1 with DEBUG flag and NRF_LOG enabled.
Usualy when my board crash i got into some kind...
Hi.
I have RF communication between nRF24L01 + and nRF24LU1 +.
Incorrect data is transmitted occasionally during communication.
So, I want to use CRC, but when CRC...
I want to get 32000 bytes per second with NRF24LU1+ ,as my audio sampling rate is 16K and sampling bits is 16.But actually I have lost one packet or more per 10ms. data loss...
Hi Everyone,
Is it possible to programmatically assign a static mesh-local EID IPv6 address to a node in a network? I would like to communicate to individual nodes in the...
I am using the nRF52832 Soc, and have a requirement of using a timer with a large timeout value, hence I want to use the watchdog timer.But as I get TIMEOUT interrupt the...