Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hi all,
If i have connect a band with my phone, then i let my band close to my notebook and let my notebook unlock.
Any suggestion about this?
Thanks in advance
Hello all,
I am working on the implementation of DFU OTA in our application, running on a custom board using the nRF51822-QFAC.
The tools that I am using are:
...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
[Update 8/15]
Here's the file for the main part of my code: sensors.c . The sensors_start() function at the bottom is where the while loop and the print statements are located...
I want to send data to my android phone from Nrf51822.My compiler is mbed I use redbearlab NRF51822 kit.For example,I want to see on my phone "hello world".
Mbed Program...
Hi,
I'm using S130 v1.0 softdevice and bootloader (single bank) from SDK v9.0.
When updating an application, I always get a CRC error at end of the upload. I generate...
Hi All,
I want to club both application into single without affecting functionality of each.
basically i want to make ble_hid_mouse example to be pair with my phone...
Hi,
I have got a PCA10001 board version 2.2.0 (2014.10). Now, I am looking for a "step by step" guide abou launching mbed on this board? Please, help me.
Regards,
Pave...
In the Master Control Panel on Android, I have a beacon that is advertising with the BLE flags set to 0x06, which is BREDR_NOT_SUPPORTED | LE_GENERAL_DISCOVERABLE. Its packet...
Hello,
I'm new to nRF51 and would like to understand if it is possible to output 5 independent PWM signals to 5 GPIO pins simultaneously on a nRF51?
Thank you.
Hi Nordic,
I am using PCA10031 nRF51422 dongle and trying to program ble-sniffer_nRF51822_1.0.1_1111_Sniffer.hex for sniffing. I have downloaded the ble-sniffer_win_1.0.1...
When initializing the S110 softdevice, I can choose between the different clock sources as defined by the nrf_clock_lfclksrc_t enum:
/**@brief Possible lfclk oscillator...
