Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
I am using an nRF51422 and attempting to interface
it with an MPU9150/6050 using your MPU6050 driver and
the underlying twi_hw_master.c.
I have modified twi_master_config...
Hi all,
My application gathers sensor data and uses the advertisement packet to broadcast the values (much the same as the nordic temp sensor example). Rather than having...
Dear developers,
I need to turn nrf8002 to master mode in order to use Alert Notifications of "Profiles - On Master" offered by nrfgoStudio. I need these profiles to activate...
I'm trying to send data acquired from the ADC and monitor it using the master emulator.
The values I'm getting do not appear to make sense though.
I'm using the BLE_HRS...
Hi,
Original UART DFU bootloader SDK example ported from NRF6310 board to PCA10001 board does not work.
What did I do wrong - can anybody please help me ? Thanks in...
It's possible this is a hardware problem, but what I'm seeing is this...
The clock is enabled on pin 0, data on pin 4. With both enabled in exactly the same way, drive...
Hi, I am trying to get the rssi value of a connection, and what I am trying to do is to start the rssi in the beginning at the connection and end it at the end of connection...
Using S110 version 6.0.0, Sdk 5.2.0, GCC 4.8 (C++, but that don't matters here).
I want to know, if the central has switched Notification and/or Indication on or off for...
Hi,
is it possible to use the PCA10000 as a data logger, to transmit the incoming data over USB to a terminal programm? Are their any limits, e.g. for the data rate?
...
Hey guys,
We're seeing a problem with weird reboots after our system goes through a firmware update using the DFU. We are using the latest GCC for these builds (4.8 2014q1...
Hello,
I was wondering if Nordic plans to offer a dual core variant of the nRF51822? We are starting to see vendors offering dual core BLE radios with one ARM core dedicated...
Hi All.
I am trying to download the Bootloader to nRF51822 Dev Kit using nRFgo Studio (32 bit, v 1.15.1.2691) but getting an Error.
"ERROR: Attempted to write to UICR...
Hi, I am trying to write code to run the nRF8001 chip from a PIC microcontroller. I've been messing around with nRFgo Studio for generating the setup data, and I've noticed...
We need to send some custom data in advertising packet.
Is it possible to use 'ble_advdata_service_data_t' with UUID of a standard service (e.g. battery service or device...
