Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
I have been forced to upgrade to the nRF54L15 from the nRF52840 DK. The example code in the SDK for the nRF52840 the 'ble-peripheral' had example code for 'ble_app_uart' which...
Hello Nordic,
I’m using ncs\v3.1.0\nrf\samples\peripheral\radio_test` to test the nRF54L15 with PHY set to `NRF_RADIO_MODE_BLE_LR125KBIT`. However, the RF spectrum measurement...
Hello,
I am developing a custom board based on the nRF54L15.
Every time I do RTT connection from the extension i have been asked to prompt the target device (nRF54L15M33...
i working bare-metal, using HW registers directly.... no zephyr, no SDC....
i'm able to successfully receive packets through the RADIO RX path, but now want to add a timeout...
Hi,
After installing nrf sdk v2.9.3 trying to build application under Windows fails with the following message:
Trying to run any command inside the NCS shell/terminal...
With nrfconnect SDK V3.3.0 seeing commissioning issues with light bulb sample with nrf52840dk and google home. The logs are given below. Please help with resolution
Thanks...
Hi,
We have an application where we have a working DFU over BLE with SDK 2.9.1 but once we have migrated to 3.2.4 it has stopped working. Something has obviously changed...
Good morning,
we are using the Zigbee stack (ZBOSS) on nRF52 devices with Green Power Sink enabled and we are integrating a Green Power door sensor.
nRF5_SDK_for_Thread_and_Zigbee_v4...
Hi, I am working with the nRF54L15 on sdk-nrf 3.2.3 and I am experiencing an unexpected behaviour with the NFC T4T stack regarding WTX frame timing.
Here is the observed...
Hi Nordic team,
I’m working on an nRF5340 project using MCUboot with the secondary slot placed on external flash.
I found a strange issue related to pm_static.yml . My...
Hello Team,
I am trying to test a PDM microphone (MP34DT01‑M MEMS) on the nRF9151 DK using nRF Connect SDK .
So far:
I have successfully tested I2C and I2S DAC audio...
The drag and drop programming was working fine on previous boards.
We just purchased 10 boards thinking that they were the same, but the don't seem to work.
PCA10040 3...
We are developing the nRF5340 for the Thingy91X based on Connectivity Bridge (NCS 3.2.4). I want to output logs from SWD and view them with RTT Viewer, but even when I call...
Hello Nordic-Team,
I am using the SENSING mechanism on GPIOs to wake up a firmware from SYSTEM OFF. Two GPIOs are used for this and it is crucial for the firmware to detect...
The spec. gives a 22V max for a limited amount of time. And max. 5.5V as recommended operating conditions.
But I wonder, what will be "inbetween", e.g. 7V for hours?
From...
