As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hello,
The following code was embedded in main function, the sdk version is 15.2.
the debug console show as below:
My question is , why string "This is a string...
Dear all,
after some customs problems I hope I finally will receive my Thingy 91 tomorrow. I have already installed the toolchain and done some readup on the device for...
I am attempting to build the new alexa_gadget example that is included in the nRF Connect SDK.
Environment information:
Windows 64-bit
nRF Connect v3.6.0
nRF Connect...
Hi everybody,
I think have a problem which involve writing on the external memory of the nrf52840, what I want is when I receive data from the NUS service I want to store...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hi,
The system has an nRF52840 as a BLE USB Dongle plugged to a PC, and connected by BLE to another device (another nRF52840).
I measure the latency time between the...
Hello everyone.
I made my own board with nrf2840 and wanted to use the CC310 module for encryption.
I uploaded an example from the SDK to my board and in the debug I see...
Hi,
I am a newbie to nRF devices. I have different sensors connected to TWI,SPI,ADC etc. and need to send these data to a cellphone through BLE. Does anyone has a sample...
Hello,
I'm starting to investigate using the nRF52833 as part of my design and i wanted to clarify the specification in the datasheet. it states the following:
Does...
Hi,
When upgrading a project from ncs 1.3.0 to 1.4.0, the clock_control_on() call behaves different; It always returns -EPERM. Did the API change?
The call is used as...
Hi everyone,
I want to modify the USBD example.
In the USBD example there's a mouse but I don't have to work with a mouse.
I want to transfer data from ADC to PC. How...
Hi, I am using the Nordic nRF52832, with v15.2 of theSDK, and would like to use "nrf_sdh_freertos_init" to implement multilink. I refer to example "ble_app_multilink_central...
I have beacon (ble_app_beacon) transmitting every 40...50 ms, nRFConnect shows adv interval is ~44 ms, so it receives ~22 msg/sec. My beacon listener gets only 10...12 msg...
Hi,
I have simple test firmware that simply connects to the network and goes into PSM sleep, it works perfectly well on the nRF9160DK but the Thingy 91 is refusing to connect...
