Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
In SEGGER Embedded Studio I am not able to connect to the J-Link anymore.
The error message says No idcode detected.
The J-Link commander program returns the following...
The SysTick port for NRF52 does not support tickless idle on freeRTOS, what is the reason for this limitation? Are there any known problems behind this limitation?
I tested the code below to make the board go to sleep and wake up on each button press. When I start, it draws 30ua, but when I press the button it shoots up to 200ua (a clear...
Hi,
We are developing nrf9160 sensor based product powered by primary battery(non rechargeable). Sensor current consumption is less than 1 mA.
while trying Saft LS14500...
Hello,
How can i put out the received Adv Data on the UART? Currently I get for every advertise packet the BLE_GAP_EVT_ADV_REPORT in my ble_stack_handler. Then i wanted...
I'm using the ble_app_hrs example code and added a new custom services with multiple characteristics . conn.interval 10ms- 15ms and need to get maximum throughput so i set...
I have nRF52840 DK (board PCA10056) . Right now I flashed LED blinking program on nRF52840 DK. It is fine.
Now I want do ADC operation, so I fed some external analog signals...
Hello, I am trying to send and recieve data with the M24C32-FMN6TP 32 Kbit (4K x 8bit) eeprom. My data are arrays with 16bit values and the datasheet says it cannot write...
Hi,
I have nrf9160 dev board.
It seems to me that getaddrinfo() has memory leak. If socket is closed, and call getaddrinfo() to reopen, it returns -10 (memory) error....
i'm looking for support in desinging modules working in zigbee network with driving this network from mobile phone by bluetooth. It has to be multiprotocol system. How should...
Hi,
I was trying to load the sample example code for Assets tracker in SEGGER Embedded Studio for ARM V4.20a but i encountered with some error.
Transcript & Output:- ...
Hi everyone. I've implemented kind of simple FW updater. The purpose is to copy FW from flash (0x0 address, no MBR or SoftDevice) to RAM buffer on node1. than send this FW...
The most recent nRFConnect AppImage version (3.2.0) fails to launch on a Debian system due to chrome-sandbox file permission errors.
Steps to reproduction:
1. In a recent...
I'm using nrf52832 DK and SDK V 15.3 and SoftDevice S132 . I have created a custom services with 5 characteristics. So i want to get maximum throughput so i increased MTU...
Hi
For our semester project, we develop a box that has to reads some parameters from an oil pump system and send data to the cloud. As we wanted to make it independent of...
