hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Are there any particular practices or instructions should i follow if I want to write a custom library
We are trying to write a library for LEACH protocol and it is a network...
I spoke with someone at Nordic who seemed to imply that utilizing the radio does not necessarily tie up the Cortex processor on nRF5X devices. Is this true? It seemed to me...
I am trying everything.
In sdk_config: #define UART_DEFAULT_CONFIG_HWFC 0
In the nrf_cli_uart.c I changed it to APP_UART_FLOW_CONTROL_DISABLED,
in the pca10040.h I...
Hi , I have 2 nrf51822 borads. One is with nRF5_SDK_12.3.0_d7731ad\examples\ble_central\ble_app_hrs_c and the other is with nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral...
I would like to use the ble_app_uart_c example, found here , to connect to a custom peripheral. What values should I change in the central device code in order to connect...
I know that BLE is not suitable for high-volume streaming.
So how do BLE earphones stream audio?
Does it use with bluetooth classic protocol?
And I coundn't monitor...
Hi,
I've one central and one peripheral devices. I'm trying to make a connection between them, perform a bonding process and finally add the peripheral id in the whitelist...
Hello All
I am developing BLE based home automation system using nRF51422 DK for my research activities. now i am planing to make separate PCB nRF51422 device alone. i...
Hi,
I'm trying to get the RSSI of incoming 802.15.4 packets using otLinkRawGetRssi() , but I need only RSSI from one specific device. I tried to use whitelist ( otLinkSetWhitelistEnabled...
Hi, I ran the example code ble_hrs_c in nrf51822 16KB RAM version and 32KB RAM version. The 16KB RAM version works fine. But in the 32 KB RAM version, peer_manager_init(true...
I modified the HTS app in the nRF toolbox to test adding other services like below.
In detail, I added mDICharacteristic field to save the information of System ID...
Hello,
I developed a Nordic board with 2450AT18B100 chipset antenna. I follow the design of Solar Powered Sensor Beacon.
infocenter.nordicsemi.com/index.jsp
I test...
Hi, I'm building a product with use this kit www.nordicsemi.com/.../nRF52-DK and I would like of know how write the firmware in others CIs to can use in my circuit board....
Hello,
I am currently working on project that uses BLE peripheral and BLE central for automatic sensor calibration on custom board. There is an initial connection where...
Helllo All,
I designed on custom board (nrf51822 and used 4 programming pins(swck,swi,gnd,vcc) but how to program/flash the soc?which segger i need to purchase?
