hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Edit 1
To narrow down I did this... Below is ble_dfu_init() from ble_dfu.c.
uint32_t ble_dfu_init(ble_dfu_t * p_dfu, const ble_dfu_init_t * p_dfu_init)
{
uint32_t...
I am running NUS and a custom service.
I have updated vs_uuid_count = 2 in softdevice_handler.c
Following other posts on the forum, I have stepped through the code using...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Hello everyone
I was not able to find any explicit statement regarding the use of the TWI_APP with easyDMA on the nRF52 series and SDK13.0.0.
I checked the examples...
Hello guys,
I am currently looking at the recommended schematic QFN48 with internal LDO setup and I have a few questions (sorry, if they are silly, I am a newbie).
...
Hi, I'm working on an extremely space-tight design and need some clarifications. It is an nRF52832 QFAA chip with a Johanson 2450AT18B100 chip antenna.
Up to this point...
Hi,
I would like to use higher dBi antenna instead of the DK pcb antenna. Can I say the pi-network before J1 (measurement point) probe is 50ohm? Hence I can just remove...
I am trying to control another BLE device with nRF52xx. For controlling the device I need a terminal for connecting, disconnecting and switching on & off a sensor. I have...
I am using NRF52DK and trying to debug an SPI transfer, using SEGGER_RTT.h to print. However, printing of the logs are not consistent. Some debug lines do no appear in the...
Hello,
The only semi-official information that I can find regarding the differences between PCA10040 1.1.0 and 1.1.1 DK boards is this post . It suggests that there are...
I recently ordered two NRF52840-PDK and a Segger J-Link Base to program/debug the boards.
Then I just read that the development kit have a J-Link OB included, or I could...
Hi.
I wonder that how to setting continuous modulated output mode for nRF24L01P.
I see Appendix C - Constant carrier wave output for testing in datasheet.
But there is...
I see in the SDK 13.0.0 release notes that the NFC type 4 library was updated to "production ready", but I couldn't find a summary of the changes made to the NFC Type 4 library...
