dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi
Im trying to figure out how to migrate my quite large older project from and softdevice s132 to using s140 (SDK14.1 )in order to experiment with long range.
Besides...
I was looking at the nRF52832 used for Bluetooth modules. And I was trying to understand the Analog to Digital converter in the nRF52832. I was wondering if anyone had or...
I'm trying to make the initial connection and flash/debug my adafruit NRF52840 express through a Jlink EDU to SWD on the NRF board. I am trying to flash to the board in the...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hi,
We are trying to install the nRF toolchain/SDK/SES etc. so that we can compile (modify for NB-IOT) and evaluate the nRF91 asset tracker.
We have followed all the steps...
I am trying to use a button to put the nRF9160 to sleep and to wake it back up.
I configure my button as follows:
gpio_pin_configure(dev, PIN, GPIO_DIR_IN | GPIO_INT...
Based on mesh3.1 sdk15.2 Can I add DFU service to light switch server? Used to upgrade firmware via APP nrf Connect? I added a dfu service to the light switch server with...
Hello,
I wrote the code for HT1632 using SPI Protocol
while debugging when it comes to below function it will stop debugging
HT1632_5X21_init( LED_MAX_DISPLAY_X, LED_MAX_DISPLAY_Y...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
Currently with one device...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I am using FDS module to write into Flash. I...
Hi there,
I' d like to develope dfu by receiving byte stream (mimeType) over USB or UART
I am almost newbie for developing dfu.
I already checked dfu over ble and...
Dear Nordic,
I try to compile the Keil project inside the thingysdkv210.zip file but it does NOT work.
I use Keil uVision V5.24.2.0 on Windosw 8.1.
There are so many...
Hi,
the evalboard seems successfully implementing the command start_rx_sweep by placing the receiver in the sweep mode.
infocenter.nordicsemi.com/.../nrf_radio_test_example...
Hi,
I am trying to connect with nRF9160-DK to our local network. After first restart of the device I was able to connet to the network, but straight after that Asset Tracker...
Hey, I am trying to incorporate an app timer using the app timer function already on the code in the central and peripheral examples of the SDK for the UART examples. Specifically...
