As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
i am using redbear blend v2.0 where based on nrf52832, i try to execute ble_app_blinky examples code on nRF5_SDK_15.0.0_a53641a using uVision, but after i change some configuration...
I'm unable to get any example code to test the timer in counter mode, I see the data sheet and trying to enable, but its not working can any one suggest me how to start the...
Hello,
I believe there is a documentatin error in document nan_40.pdf CIRCUIT BOARD GUIDELINES FOR aQFN PACKAGE.
Table 3 / Page 11
Hole size of blind via is mentioned...
Hi, I have some questions about GPIO interrupt.
Now, I want to know the state of the pin, So I use the gpio_pin_read(PIN) to get the state. But when the pin is suspended...
hi,
i am working on a project were i have to discover all the service on peripheral device and fetch data from it like nrf connect app.
so i am using nrf52832 with sdk...
Hi team
I have a problem that bothers me for days.
I try to run demo ble_app_uart_c with
NRF_SDH_BLE_CENTRAL_LINK_COUNT=8 and NRF_SDH_BLE_PERIPHERAL_LINK_COUNT=1...
I used to program my PCBs using the nrf52840 PDK, however, my mac no longer recognized the PDK. The PDK turns on and the application runs as LED 4 blinks but the LEDs next...
hi,
i am using ble_uart example to take time when data arrives and time when data being sent over bluetooth.
when i prints the time without connecting to bluetooth. then...
Board:custom board
Mesh SDK: V1.0.0
IDE:SEGGER Embedded
Problem a：
When I test the steps specified by “Interactive PyACI”, there is A certain probability of Provisioning...
Hello,
i asked this quastion once in this thread: https://devzone.nordicsemi.com/f/nordic-q-a/32444/reset-on_ble_connect-when-button-event I accepted the given answer but...
Hi Nordic Team, I'm trying to setup a gcc/eclipse based environment according to gustavovelascoh.wordpress.com/.../ on Linux/Ubuntu 16.04.1 64Bit. The Ubuntu system lives...
Hi, I would like to make an exact copy of the nRF51 dongle antenna (as was recommended by multiple blog posts by Nordic). I am concerned about the legal issues, and any IP...
I search GPIO pin bit definations and register. I saw pca10040.h GPIO defined.I dont know how to configurated P1DIR, P1EN, P1OUT etc.. I studied Texas Instrument before. I...
Hi,
I'm making my own prototype board using the nRF51822. this board is powered by a rechargeable battery lir2450 (3.6V): www.powerstream.com/.../Lir2450.pdf
i want...
Hello world
after several hours & day, Finally I have to implement this KNN code and nRF51822_adxl345 code. I have implement to one. but there is problem that..
I can...
