Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I would like to build two boards that can send small messages between them, at long distance. For that I would like to use some of your devices (I used 51822 in...
Hi
I have working module which communicates via uart with another module. It works good, unless it is heated to 40C. After that temperature UART communication is not correct...
Hi Engineers!
We made our own ten (10) PCB's with nRF52840 MCU onboard fully according to "Circuit configuration no. 3":
1. LDO only mode (VDDH connected to VDD connected...
I have a custom circuit with nrf52832 which I am trying to program.
All i/o pins seem to be working fine except pins P0.06 - P0.10.
I'm testing it with mbed (digitalout...
Hi,
Thanks for taking the time looking into issue.
We are using Keil uVision 5.14.
Our target is a custom board (BMD200 eval Module based on nRF51822)
We were able to...
Hei guys,
for a new custom board based on nrf52832 where i have to minimize power:
have an external Li-Po battery, with a cutoff @3.0v, so the range will be 4.2v...
blesc_pairing_dhkey_check_failed.zip
Hello,
I used the example ble_app_multirole_lesc and paired with nRF Connect app. However I got the error message (in Bluetooth...
Hi!
So I have my GATT value of a service that I would like to update.
Sadly that value always stays at the initial value.
Below you can find my update function.
uint32_t...
I am using SDK12.0.0. ble_app_uart example, and I have change the clock to using LFCLK RC. I know from nRF51822-PAN_v3.1.pdf that we need to calibrate the LFCLK RC after reset...
I've managed to overcome all the quirks in setting up Eclipse/gcc development with the nRF52 PDK (PCA10056), and I can build the sample projects just fine. Here's my issue...
I arrived at step 8 in this tutorial
github.com/.../custom_ble_service_example
Now I'm supposed to propagate events to the application, for example connection state...
I am using a usual uart to bluetooth application and it works great, but I would like to set this application to be a known apple midi device, it seems I only have to add...
When running ble_peripheral\ble_app_uart example..... Of course I am a little bit
corrected.....
Beacons occasionally stop.
Despite the following settings:
#define...
