I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
hi all,
i try to use to timer to have a single press and a long press.
this my code.
const nrf_drv_timer_t TIMER_BUTTON = NRF_DRV_TIMER_INSTANCE(0);
const nrf_drv_timer_t...
I don't know where it is used..
example, when I use sd_ble_gatts_hvx(conn_handle, &p_hvx_params), conn_handle was BLE_GATT_HANDLE_INVALID(0x0000) result of debugging. ...
I use nRF5_SDK_12.2.0_f012efa to develop BLE application in IAR workbench. Now I want to test the example: ble_app_template_pca10040_s132-nrf52832_xxaa. The project can pass...
First off, I have worked through Vidar's excellent tutorial located at " devzone.nordicsemi.com/.../" and have successfully built and run the blank blinky example so my installation...
Hello,
I am trying to change the MAC address of my device nRF52, by using NRF_FICR->DEVICEADDR[0], NRF_FICR->DEVICEADDR[1], I am able to see the device address.
But...
Hi I am using SDK 12.0.0.0 in nRF52832 in this code when I am using __enable_irq(); function for enable the interrupt then controller is getting reset can anyone help me regarding...
Hi,
I was trying to plot incoming ADC variables using Keil Logic Analyzer function inside the IDE.
So far no success; I am able to use it when using STM32 board.
...
I am getting confused when using nrf_gpio_cfg_input(PIN_12,NRF_GPIO_PIN_PULLDOWN)
should i keep it as NRF_GPIO_PIN_PULLDOWN,PULLUP or should i use NRF_GPIO_PIN_SENSE_HIGH...
Hi!
Using the out of the box ANT shared channel demo with a NRF52-DK board and the iOS demo app everything compiles and installs nicely, using the Android-based app nRF...
I'm working on a proximity beacon application using the nRF51 DK and a Nordic Beacon. The application basically has the nRF51 DK connect to the Beacon and monitor the RSSI...
Hi All,
Just want to ask if there is a better or recommended way to manage priority interrupt.
My application uses 3 interfaces:
SPI as master to interact with...
Hello,
I have an BLE application were I want, for security reasons, to allow a connection only if a button is pushed or if the devices already have bonded before. The Button...
Hello lovely Nordic Semiconductor staff (and everyone else reading this),
I have recently been working on exploring the use of BLE via Nordic chips in my employer's products...
Hi,
How to store two application image in nrf51822 flash each image size is 60kb. I have enough space
To store images but I don't know how to store. Please guide me to...
How can i reaed 32bits word using spi ?
I don't find the function to configure the SPI to read 32bit word ?
And how top start reading ? Is this function"uint8_t nrf_spi_rxd_get...
