I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello,
I received the above error using NRF5 SDK 12.2. I have modified "nrf_drv_config.h" so that it reads #define TWI0_ENABLED 1 . Also, I put #include "nrf_drv_config...
Using nrf52 DK , SDK 12.2 , and armgcc.
I want to use BLE_UART but I also want to bond.
I started with the BLE_UART example code and added peer manager and FDS.
I...
I've been trying to track down a bug where a couple of my Central test devices, a Nexus 5 and 7 (Android 6.1), won't send a connection request to a peripheral they're bonded...
Hi
I have a problem on testing the HRS examples on SDK12.2.0.
When I use a android phone, running on version 6.0, using nRF Toolbox version 2.2.1 App, to connect to the...
Hi!
After reading nRF24L01 product spec, I'm really unsure:
Spec. says: "The input signal should not have amplitudes exceeding any rail voltage."
"rail voltage" it's...
Update 1/27/2016
Just reviewing again the pins + schematic; I am using the following pins:
SCK P0.07
CS P0.08
MOSI P0.06
MISO P0.05/AIN3
Looing at the...
After i test a lot of possible configurations for nrf24L01+ based on the documentation, i didn't come to the right setup for all the nRf24L01+ registers to send data from...
Hi,
I'm using Windows and I am following this tutorial.
I am at the point where I need to write make at the example project.
I get this error
as warned in the...
Hi,
I'm trying to get a general idea of how the radio will perform near the bottom end of the supply range.
Our product concept is currently designed on a system voltage...
Hi,
I stuck on SOFTDEVICE_HANDLER_INIT in example code on nRF DK PCA100028 within debug.
It is example code from SDK 7.1.
How Can I solve this?
Why Nordic's SDK...
Hello,
I am developing an an system and I am at the stage of optimizing for power.
I using NRF6707 ( Very helpful !!) to measure current.
I cut SB9 of NRF52 DK and have...
Hi,
Can I try to discovery services for the next connections while it is performing for the other connection?
I use "ble db discover" manager.
And I cant find this...
I'm using nRF52DK and SDK12.2.0.
Trying to change MTU size.
When I modified app_nrf_uart example as below
#define NRF_BLE_MAX_MTU_SIZE 103
Then infinite reboot...
I am working on a project and have successfully implemented single channel PWM to dim leds (using a transistor FET).
The pwm init code is below:
uint32_t err_code;
nrf_drv_pwm_config_t...
