I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
hello,
I recently updated SES and got a new version of nrfSDK.
Secure_boot sample does not contain Cmake. In other SDKs on github secure_boot does not exist.
is...
What is the best way to filter info center results to match my project? I'm using SDK 1.5.1 for S132 and I think that is softdevice 6.0.0.
It would seem like a simple top...
We are currently running on mfw_nrf9160_1.0.1 and NRF master as of today (Sept 13, commit 224bee9).
We are developing an MQTT application that uses TLS mode sockets.
We...
52832 & s112 & sd6.0 & sdk15.0
If you have multiple pairings on the same host will return error by “pm_device_identities_list_set”
err_code = BLE_ERROR_GAP_DEVICE_IDENTITIES_DUPLICATE...
Hello everyone,
I trying my nrf52832 getting ultra low power current conception mode using System OFF mode (0.3uA). I using SDK 15.2 ble_app_beacon example I change 32KHZ...
I started developing on the Adafruit nRF52 module. I wanted to make a custom PCB to demonstrate a prototype and fabricated a board with a MDBT42Q module from Raytac. I sent...
Hello, I have used the nrf52840 . I have created applicaction from existing examples of SDK which used bluetooth. And now want to add OTA via bluetooth. Is it possible use...
Hi,
I am developing an app based on PCA10059 dongle. my program work fine on this dongle, but i have a problem with it. after programming PCA10059 dongle with my firmware...
Like the title,
Is it possible to disconnect ble link or stop advertising at runtime, then change the service uuid and characteristics?
I wanna to do OTA service in application...
I am able to receive motion data [rawdata] from thingy52 on my RPi 4 using bluepy library in Python3.
I want to extract the raw values of Gyro/Accl/Mag from sensor.
The...
Hi,
I'm writing a program that swaps between LTE and GPS to send the device's location to AWS over MQTT. I am able to connect to LTE and AWS, then swap to GPS and get a...
Hello. I 've got such problem with flashing some of the ESB protocol examples of NRF5 SDK. I use Adafruit Feather NRF52832 board with ST-LINK V2 debugger. https://www.adafruit...
I want to implement UART service which can act as central and peripheral at at time.
I am using nrf52832 board and sdk 15.
I tried to implement it by changing the services...
Hi,
I am following the nRF_Sniffer_UG_v2.2.pdf to setup the nrfSniffer. Wireshark does not show me my board among the interfaces. I had a look at the troubleshooting part...
Hi,
We are developing a Bluetooth 2d-3d mouse with OTA -DFU service.
The controller we are using NRF52832 QFABB0 it contain 32KB RAM and 256KB of flash memory.
SDK...
