S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
hi all,
i try to use to timer to have a single press and a long press.
this my code.
const nrf_drv_timer_t TIMER_BUTTON = NRF_DRV_TIMER_INSTANCE(0);
const nrf_drv_timer_t...
I don't know where it is used..
example, when I use sd_ble_gatts_hvx(conn_handle, &p_hvx_params), conn_handle was BLE_GATT_HANDLE_INVALID(0x0000) result of debugging. ...
I use nRF5_SDK_12.2.0_f012efa to develop BLE application in IAR workbench. Now I want to test the example: ble_app_template_pca10040_s132-nrf52832_xxaa. The project can pass...
First off, I have worked through Vidar's excellent tutorial located at " devzone.nordicsemi.com/.../" and have successfully built and run the blank blinky example so my installation...
Hello,
I am trying to change the MAC address of my device nRF52, by using NRF_FICR->DEVICEADDR[0], NRF_FICR->DEVICEADDR[1], I am able to see the device address.
But...
Hi I am using SDK 12.0.0.0 in nRF52832 in this code when I am using __enable_irq(); function for enable the interrupt then controller is getting reset can anyone help me regarding...
Hi,
I was trying to plot incoming ADC variables using Keil Logic Analyzer function inside the IDE.
So far no success; I am able to use it when using STM32 board.
...
I am getting confused when using nrf_gpio_cfg_input(PIN_12,NRF_GPIO_PIN_PULLDOWN)
should i keep it as NRF_GPIO_PIN_PULLDOWN,PULLUP or should i use NRF_GPIO_PIN_SENSE_HIGH...
Hi!
Using the out of the box ANT shared channel demo with a NRF52-DK board and the iOS demo app everything compiles and installs nicely, using the Android-based app nRF...
I'm working on a proximity beacon application using the nRF51 DK and a Nordic Beacon. The application basically has the nRF51 DK connect to the Beacon and monitor the RSSI...
Hi All,
Just want to ask if there is a better or recommended way to manage priority interrupt.
My application uses 3 interfaces:
SPI as master to interact with...
Hello,
I have an BLE application were I want, for security reasons, to allow a connection only if a button is pushed or if the devices already have bonded before. The Button...
Hello lovely Nordic Semiconductor staff (and everyone else reading this),
I have recently been working on exploring the use of BLE via Nordic chips in my employer's products...
Hi,
How to store two application image in nrf51822 flash each image size is 60kb. I have enough space
To store images but I don't know how to store. Please guide me to...
How can i reaed 32bits word using spi ?
I don't find the function to configure the SPI to read 32bit word ?
And how top start reading ? Is this function"uint8_t nrf_spi_rxd_get...
