Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi, I use S110 v8 in my application with DFU support. When DFU is triggered from application (by writing 0x0104 to DFU service control characteristic), then application fails...
Working on a project i want to update the nordic application (firmware) from other MCU, i am having some problem to compute the crc.
How to we calculate the crc of...
When I plug the nRF51822EK (PCA10024) in via USB while holding the reset button down, it mounts as "MBED LOADER" rather than "MBED". This page
developer.mbed.org/.../ ...
Hi,
I have a nordic chip (nrf2832) and I am trying to use it as a LWM2M client and register it to a LWM2M Server. I want to achieve this:
developer.nordicsemi.com/.....
I'm trying to update my SoftDevice with a bootloader, which is basically the same as the one in nRF5_SDK_11.0.0_89a8197. The image is saved in bank 0 and is validated by dfu_sd_image_validate...
This is my first DFU project, and so this may be super-obvious to all of you.
I am writing this here to help others, because it appears that there are others out there...
I have an mBed application that uses the S130 SoftDevice and polls data from a couple of other connected peripherals via I2C & SPI.
I use a Ticker object, which seems to...
Hello,
I use the example dfu_dual_bank_ble_132 in the nrf5x sdk 11 (PCA10040).
I have had my programe before the OTA, i will have a programme wich would update at any...
Hi all:
I stored some settings in flash in the address 0x00077000 and this address is got by the function of pstorage_register().
However this area will be erased by...
Hello there,
I've been trying to use embitz (the new version of emblocks) to program a nRF5188 but i always fail to compile the "ble_peripheral_hrs" exemple, i'm always...
Hi
I have a unit that is rather old and I want o update it to the latest softdevice.
In the unit there is a bootloader and softdevice version 6. Does anybody know if it...
I'm making progress, but still struggling to get the sample DFU built into NRF Toolbox to download successfully with my bootloader. Using hrs_dfu_s130_*.zip.
For this,...
I tried if there is a possibility that my device would brick if I interrupt the DFU process. notice that I'm using SDK10 with dual bank bootloader. I uploaded the app over...
I am going to develop on nrf51822 and the data sheet says nrf51822 is s110.
I want to load an example of sdk 11 but there is no example for s110.
I am a total newbie, so...
