Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello,
I would like to use the nRF52840 for a wearable. It should be powered by a lipo-battery with 3.7V. Therefore I would solder it to the VDDH and Ground Pin (VSS). Is...
Hello .
I try to connect my JLink to my nrf51422QFAA cunstom board. And I use J-Flash to test ifg it can readback and it is OK. But When I try to use nrfjprog, I got some...
We would like to create the boot settings page and merge it with the application and flash the merged hex file using J-Link and nrfjprog.exe in production.
Currently in...
Hi,
We are looking for a secure NFC solution for our application. We want to make sure the tag is secured (cannot duplicate) and the reader, which is a NRF52840, needs to...
I am using SES V4.18 with SDK 15.3.0.
In sdk_config.h, I have set APP_VERSION_MAJOR and APP_VERSION_MINOR etc...
Is it possible to add these numbers to the output file...
I recently added Mesh DFU support to a project that I'm working on but it's extremely slow. It will take at least 1 hour to update the network under ideal conditions but I...
Hi,
My stack is
s112
SDK 15.3
Segger
nrfConnect
nrf52832 DK
Power profiler kit connected via USB to my MAC to get the traces to run.
CR2032 batter removed...
Hello
I cannot load the Radio Test code onto the Nordic NRF52 devkit. I'm using SDK15.3 and the project located at C:\nRF5_SDK_15.3.0\examples\peripheral\radio_test.
The...
Hello,
I noticed this weird bug that coincides with the SD card not initializing using the FATfs.
Basically, I have the SCLK pin of the NRF52DK connected to a breadboard...
Hi All: I am using NRF51802 ,SDK is 12.30 version, and softdevice is s130 2.0.1 version. using keil MDK 5.23 Version. And download the softdevice using nrfgostudio and keil...
Hello,
I have a nordic nrf52840 on board, with another MCU (Cortex-M4) on board. Both chips are connected over UART.
I want to use the Cortex chip to perform firmware...
Hi.
We have a strange issue we are seeing with a nRF52840 where scanning fails, but it is very rare.
Setup - nRF52840 is a central device, and there are 20 x nRF52832...
Hello Nordic!
I'm developing with s340, nrf52840, and sdk 15.3.0
My device is a peripheral and the phone is master in ble.
I listen to my coworker who is developing...
Hi, I'm trying to set P0.20 pin as MISO of my spi master to communicate with ADXL372 accelerometer sensor, but when the miso is disconnected the signal received matches with...
Hello.
I want to develop a custom bootloader able to update firmware version Over-The-Air (BLE)
I'm using a custom Dev Board based on nRF52832 with and nRF SDK V15.0....
