Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I am currently working with the asset_tracker example and sending information by LTE-M of environmental and GPS data. I wanted to know if there is any way to calculate...
Hi,
I want to test eddystone example with nRF52833.
The default project doesn't include PCA10100.
I am trying to create one, but it always stuck in the function nrf_crypto_rng_backend_init...
I believe from reading some of the existing posts that my JLink EDU mini programmer (with SWD connection) should work with the nRF51822 (it shows up as a device option in...
Hi,
I want to build a bluetooth central example of zepher to nrf52832.
I am using the command "west build -p auto -b nrf52832_mdk samples\bluetooth\central" to build the...
I'm using 51822 QFAC, SDK11 S130 2.0.0.
I'm able to write to flash using fstorage_write() below. But the problem is whenever I put a for loop after I call fstorage_write...
Hi,
I built a simple custom board with an nRF52832 ebyte BLE module with no added components except for the RST and DFU buttons, the serial wiring are the same pins (RX...
Hi,
I'm working on a BLE scanner which need collect data from the beacon's scan response packet.
As far as I test, the current mesh beaconing example cannot get the scan...
I plan to use nrf52840 in high voltage mode (connected directly to the power source via VDDH pin) with button.
And I plan to use voltage regulator with EN pin (with pull...
The most relevant thread on this topic is two years old. I do not want to use Keil as it is so costly and the project may not go anywhere. I am not interesting in using the...
Is it possible for me to easily modify the nrf52 Zigbee samples to run on 1 or more of my 5340 M33 cores, or is it a rewrite?
I can see chip support for nrf52 but no mention...
Hello,
We recently sent a design to our board assembly house for review and they indicated that the large copper area under the nRF528323-CIAA (WLCSP) may result in head...
I’m using nRF52810 on a custom board (for our own application) using SDK 15.2.0 v6.1.0 S112. Given the amount of memory this chip has (192/24 KB) is it possible to implement...
I'm using the nRF52 DevKit with nrf52832 SoC. I connected a UV Sensor through the TWI interface (PINS 26 & 27, as well VDD and GND).
However, I fear it's using a lot of...
Hello,
Till now I was using nRF52840 with nRF5_SDK_16.0.0_98a08e2 and its working fine. Now I thought to cross check with nRF52832.
When I run FDS example I am getting...
