Hi there, I'm new to the nrf/zephyr sdk and while using the nRF5340dk board, I've found that the pin1.01 is pulled high right after the board powers up. My assumption is that...
How do I power the nRF9161 DK with a battery? I have a spare 4.2V-3.7V lipo (2000mAh) but according to the docs, VIN ne eds 5V, so any recommendations for a compatible battery...
Dear Support Team,
In the project, I'm working on thingy91:nrf9160 board. Our test case scenario is to connect to cellular network(NB-IoT) and acquire GPS fix for which...
HI
We are mass producing products using nRF52832.
However, during production, a PCB was found to not detect low battery voltage for about 5%, so we are inquiring about...
Hi,
we have npm1300 device on our customized board,
without using any of the regulators, LEDs are not connected.
Gpio 0 and Gpio 4 is connected to main MCU.
when activating...
HI ALL,
I used a system off demo and added the following content.
The power consumption tested was around 1uA, which should be normal according to the errata. Then...
I tried running the official ranging example with nrf5340dk.
Bluetooth: nRF Distance Measurement with Bluetooth LE discovery
Usage
This example can obtain distance test...
I have been trying to get a arduino UNO and arduino Leonardo to communicate with the nRF9160DK but have not been able. That accounts for the SPI example aswell as the I2C...
Given that Zephyr RTOS is not certified for use on Medical Devices, is there any plan to support operating systems with FDA 510(k), IEC 62304, IEC 60601 certifications?
...
I'm looking at augmenting the GPS system of the nRF9160 (at the moment due to high current and long time to acquire, easily lost sats/location) with some geolocation. Specifically...
I met a question here. Hope anybody can help on it, thanks.
I'm evaluating whether it is feasible to run the FFT algorithm on zephyr LTS project, with the nRF52832 board...
I want to know the upgradation process of firmware (Zephyr OS) on nordic nrf52840_pca10056. I have flashed the Zephyr OS on chip once via Jlink/JTAG, and now I want to flash...
Hello,
We are developing a product which includes qr code reading as its feature.with reference to https://github.com/NordicPlayground/nrf52-ble-image-transfer-demo
as...
Dear All,
I need to develop a low-power application that sends a UDP message, waits for a certain amount of time (5 seconds) for a response and if there is no response it...
Hi,
Scenario : Scanning non mesh BLE packet with different stacks.
H/W Device - nRF52DK
Observation :
Case 1. Non Mesh BLE Stack (Soft device):: Here able to receive...
I'm working nrf52 DK, SDK V15.3 , S132 . I have created custom Services and characteristics its working fine. I need to change gap parameter in some cases because i need to...
Dear,
THINGY:91 / nRF91 DK
Currently, Power Saving Mode (PSM) is a feature that is not always available with roaming cards, and we must use the local sim card to use GPS...
It used to be downloadable, but now it's like this
The chip has the old code, and the chip can run the code
Is the chip's sdwio and sdwscl pins broken Or...
Hi,
Now I installed SEGGER Embedded Studio. But I got a activation key from SEGGER. I put the activation key into the IDE. After the I checked in the path "tools->License...
Hi,
I've seen the results of the power profiler, but I'd like to confirm this - with no other concurrent user CPU processes (standby/sleep), is the S132 softdevice guaranteed...
HI ,
I need the nrfutil commands used to generate the following zip file
softdevice only
bootloader only
softdevice + bootloader
softdevice + bootloader + application...
