Hi Nordic Team,
Previously, with the nRF52840, we could use the internal ADC channel to directly measure the supply voltage (VCC) for battery monitoring without external...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hello,
I am working with the NRF5340dk, nrf7002ek, and PPKII. I am unable to get the DK to power up with the PPK. I used a knife to break the trace but for some reason...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Somehow a program I have running on a nrf52840-DK board will enable protection. This kind of screws up the small application I am testing because it seems to lock out the...
Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
Hi,
I have nRF9160 DK. I want to update firmware to (From Your WebSite: Link Pasted)
nRF9160 LTE-M/NB-IoT/GPS Modem firmware
https://www.nordicsemi.com/Products/Low...
Since nrfConnect Programmer, ninja flash/west flash ALL use nrfjprog behind the scenes, I wish I could find out _exactly_ which nrfjprog commands the nrfConnect Programmer...
Hi,
I'm trying to reduce the current consumption. I can't use sd_power_system_off because I don't want my device to rest when it wakes up. So the other way to do this is...
Can i commuicate over USB CDC on holyiot nrf52480 by giving Vbus(5v) , D+,D- , gnd from pc. and get output on VDD or do i have to also supply voltage on VDD(3V) ? I wanted...
Using nrfx_timer_extended_compare I would like to periodically adjust the compare value of a running timer. It seems to work without disabling the timer before this and re...
Hi，
Dear， I have a question about Fstorge and Bootloader. If my app layer calls the Fstorge API to store some data, will the data saved by the Fstorage API be erased when...
Hello All,
I am running into a mesh assert error when running the light switch server demo on a custom board w/ the NRF52840 (MDBT50-1M). The device starts up fine, has...
Hi all
I am studying mesh example such as light switch server, I use Segger Embedded Studio to comple the project of light switch, it is OK, but when I want to do online...
Hi,
I'm developing a BLE DFU controller with bluepy on a RPi3. The peripheral that is being updated is a nRF51 device on SDK 12.3.0, with the secure bootloader and experimental...
Hi,
In our project we want to use nRF52832 chip using HCI Command interface. We are trying to use Zephyr RTOS project for geting HCI interface through UART. We are using...
Hi,
In y project, I want to implement CTS. Until now it's been working, but I don't know why, I now have this problem: Current Time Service not found on server, which means...
I am using a Sparkfun Pro nRF52840. I wish to communicate with it serially. I found the UUIDS it exposed : UART Service = 6E400001-B5A3-F393-E0A9-E50E24DCCA9E TX Characteristic...
Hi,
I am using nrf51 dk with sdk 12.3 and softdevice S130 bluetooth module using Keil IDE.In our project we need to send sensor data from the nrf51 bluetooth module to another...
Hello,
I want to add central-role features to my peripheral firmware. I've already managed to get this work. The strange thing, I only get one BLE_GAP_EVT_ADV_REPORT. So...
