HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
this is vishal from VVDN tech working as a Hardware design engineer .
In our project we are going to use 10k module of LTE EC25E.
So we need step file from your side ...
Hello,
In ble_app_blinky code,I cant understand this line "#define APP_BLE_OBSERVER_PRIO 3" and what does the value 3 represents here??. Is this value constant or can be...
Hi,
We have been developing our system around nRF52840 and we are now looking closer into the real-time performance of the MCU & SDK. The scenario is simple: a signal ‘YELLOW...
I am trying to add the valid range descriptor to my measurement interval characteristic in the Health Thermometer. This is a necessary step as my measurement interval characteristic...
Hi
I am using the ble_app_blinky's lbs application, as found here in the 14.2 service
C:\Eran\Software\Nordic\Packages\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a...
Hello,
We have an application on Iphone running with our custom service :
uuid : 0000fdF9-0000-1000-8000-00805f9b34fb
and our characteristics :
char-handle 0x16...
Dear Sir, we are developing an application on the nRF52840 kit with SDK 15.0.0. We are using Keil as compiler. In our application we need to receive data from two uart together...
Hi Everyone,
I have two task in which i am receving data from bluetooth and if i receive a particular hex value , i want a task(which is Toggling LED State) to run on...
Hi,
I am trying to to port ble-mesh code (serial example) into ble_app_uart. I am using nrf5_SDK_forMesh_v2.1.1 and nRF5_SDK_15.0.0_a53641a on DK-N52832.
After merging...
Hi,
Earlier today the forum appeared empty and none of my old posts were visible under profile > questions. Another user also had this issue. The front page looked like...
So I'm trying to follow this tutorial - https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader to generate secure OTA DFU
I've got...
I have set up a simple test to check if scan request can be used as an acknowledgement for advertising packets. I send some distinct advertising packets and multiplex them...
Hi everyone,
sadly my nRF51-DK boards seems to be terribly bricked.
During firmware update nRFgo Studio (on Windows) stopped responding.
I can't enter bootloader mode...
