Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I am making a project with the nRF52832.
In this project i must configurate another chip with SPI.
The timing must be very accurate. Now the problem is that the...
Hi Team,
I am using nRF52832 to implement smart watch product and it is now close to PP stage.
Currently our product testing engineer found that in a relative noisy environment...
HI. I used a translator.
I want to control the mouse and keyboard using HID with the nRF52840 PDK.
I found the HID example in SDK15 and compiled it
The Infocenter...
Hello,
The sd_softdevice_enable never returns, how can I investigate please ?
With my Jlink probe, it's look halted at address 0x000008CC.
Configuration:
SDK 15...
I''m trying to run a piece of PERIPHERAL example code running on a nrf51422 devboard
I'm using sdk 8.0 and the example's relative path is:
>nRF51_SDK_8.1.0_b6ed55f\examples...
Hi, We have a BMD300 nRF52832 acting as a BLE peripheral connecting to up to 8 phones acting as BLE central devices. We started noticing that we are getting BLE_GAP_EVT_DISCONNECTED...
Hi,
Just a small question. In the SDK 15 documentation for the Experimental: GATT Module documentation, could it be that the following sentence "The default value that the...
I can't work arround error 133 on Samsung S7. After several test I found that it's related to long advertising intervals. I've test it on nRF52 DK and nRF51DK. I've test it...
Hi, I'm migraing our project to the latest NRF5 SDK v15.0.0 (S132 v6.0.0). We were previously on v12.2.0 (S132 v3.0.0) using the BLE DFU Bootloader. I've modified our bootloader...
Hello.
I try to modify ligh_switch_demo to switch state of 4 servers. I prepared 4 custom boards (server), one client and one provisioner. Provisioning was successful. I...
Dear All,
I am using "Scheduler" module as mentioned in this tutorial Scheduler Tutorial .
I have one question. My scheduler tasks are using some SD functions which require...
Hi!
This is a general question about the Bluetooth Mesh standard and a request for some hints to your implementation.
Scenario: Say you have a remote control device...
Hi
I'm really excited about Bluetooth 5 and Mesh Networking, but I'm not sure what DK to get.
I want to make Sensor Network for Building Automation. So I can read every...
