Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
How i can see the performance like the Picture. is allways 0% and had also no time or calls in the execution profile. Breakpoints works.
But when i press F10 (Step over)...
Hi There -
I'm trying to test connection interval negotiation with a central by putting nRF Connect Desktop (Mac) in peripheral mode and requesting a connection parameter...
I have a nRF52840 application that needs to take a complex list of commands from a server.
I have a few options. I could:
code a basic language myself for these commands...
HEllo
I am using the example TWI_sensor_pca10040 with a main.cpp, and I see that there is some sort of error with the logging that I cannot point out. I get this error...
Hi
I'm currently working on the 10028 DK board, which was working flawlessly until I used the J-link RTT Viewer, and pushed the IF BOOT/RESET-button. Now, when I try to...
Hey,
SHORT VERSION:
Timer (every Second) gets started when connecting (BLE with nRF Connect) to my DK (SDK12.2, Softdevice S132). Timer gets stopped when disconnecting...
Hi There,
We have an issue where our project crashes, but the app_error_fault_handler() callback is not being called to help identify the cause of the issue. We are using...
Hello guys.
I'm newbie to embedded programming.
I'm trying to make device that can measure temperature of other objects. I have a variable resistor. The resistor's resistance...
My BLE application uses my own firmware update algorithm and bootloader, as well as the Peer Manager module. To ensure that I do not delete peer data during the update process...
I am using nrf51 running as a peripheral and an iphone app as central. It works OK when I first use the iphone app to connect to nrf51. Then I quit the iphone app and let...
Application data is stored just before the bootloader. If I do a DFU upgrade with a larger bootloader than the one currently flashed, is this taken care of? That is, is the...
i am using keil mdk5 and i want to use nrf51822.please tell me which software i need for this and which sdk i have to download for this.i am currently troubling with doing...
I'm facing problem while program custom board. I'm using nrf51822 module( link ) & j-link EDU 9.3 version. I think there is some connection issue. Here is my connection
...
Is there any reason why no error is returned when app_fifo_get() fails in app_uart_put() (SDK 12.0.0). Couldn't the lines below:
if (app_fifo_get(&m_tx_fifo, tx_buffer...
