Hi
I am using nRF52840 with SDK 15.3.
I have a project where I uses FatFS to write to a SD-card with SPI interface (SPIM3). This works very well.
I am now trying to...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with this specific exercise (l5_e2):
To ensure I wasn...
Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hi everyone,
In nRF9160 with ncs 2.9.0 I've problems when trying publish a MQTT payload bigger than 2700 bytes aproximately. In advanced I already was adequated buffer size...
Hi, I've recently acquired an nRF54L15DK, and started the development on BLE, I'm fairly new to Nordic's enviroment. In the last couple days I've been trying to build the...
Hi everyone,
I use the ble-app-buttonless-dfu example to develop my application.
I make a mutual authentication to be sure the device is connected to the right mobile...
Hi everyone,
I'm developing a BLE application where I measure throughput between an nRF5340DK acting as peripheral and an nRF52 Dongle as the central (using a Python script...
In the ANT Message Protocol doc, section 7.1.1.1, and in example code, the Device Number is treated as a uint16_t and shown as a two byte field in the flagged extended data...
Hi,
Will something interesting happen when the text segment on a nRF51 DK exceeds 64k? I am using Eclipse/gcc for developing, based on the tutorial provided by Nordic....
Hi,
I am developing a program on a Nordic nRF51 DK, using Eclipse/gcc, and am using J-Link RTT for a debug command line interface. This has worked very well for some time...
Hello,
I've been looking a bit into the nRF52 product specification and I was just wondering how powerful EasyDMA is under extreme conditions.
Let's assume the following...
I am currently working on a device using a nRF905. We want to use the device in Region 2 (USA).
This means that we need to use frequency hopping between 902 and 928 Mhz....
Hi,
I'm implementing a simple bootloader which will not use BLE.
Application will transfer the data from mobile devices using BLE and this data will be stored to...
I'm looking for a smart solution to connect my application to different ANT+ sensors and transmit a logfile to a mobilephone via BT (and receive notifications from mobile...
Hi~ Sir:
I test S120 connect with S110 have problem ,test methods are as follows
S120 connect with S110 ,function ok.
S110 Power Off and On, the interval time about...
Hello everybody,
I've been digging through the forum and the documentation for hours now. But to be honest I don't understand the whole timer thing.
I need a simple...
Hello,
while implementing a BLE link layer, I’ve stumbled over a race condition, where I have a problem to find the cause. Maybe someone of you have an idea, on how to...
I am reading data over the duration of 3 seconds on SPI, but while I'm doing that, I need to send that data over RF using microESB library.
I need to make sure the read...
I use the chip nrf51822, However, SDK8.1.0 example ble_app_uart is base on nrf51422, what I need to do? just replace bsp.c ? and which bsp.c file corresponds to the nrf51822...
I'm tring to build a FOTA broadcaster machine using a raspberry-pi with bluez. or any other Linux small linux embedded system.
The idea is that after testing the board...
I cannot program an external nRF51822 module(program old softdevice S110 6.0.0) with nRF51-DK p20 (SWD), it give message "invalid parameter error".
and i program the 51422DK...
Hi all,
I want accive this situation. My peripheral connecting a central with a service for example hrs, then i stop the conect with the function sd_ble_gap_disconnect(m_conn_handle_peripheral...
