HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hello,
I have a nrf51822 chip that I would like to flash using Segger Flasher in Stand-alone mode. When I am trying to load the program to the chip I get the following...
I'm trying to add DFU service support to my application on an nRF51 development board, using the instructions here: Adding DFU Service support to an application . I'm using...
I am not a native English speaker, I am totally confused with this line of code where I have found in many samples
#define APP_ADV_INTERVAL 300 /**< The advertising interval...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hi,
I have an issue in using GPIOTE_IRQHandler.
Let me give an explanation about our implementaiton.
we have nRF controller which is connected to STM32 controller...
Hi
Is possible to use GAP White-list to restrict connections without the bond manager system ?
Just by save the white-list with pstorage.....
for exemple, first open...
Hi,
I'm using S110 on PCA10028, I have problems with byte receiving on UART and can't make it work.
I can easily send and receive data over terminal using UART. I can...
Hello,
i use notifications with sd_ble_gatts_hvx. If I push a lot of data, are notifications overwritten or do they are fifoed ?
How to do a kind of flow control to...
So I'm just getting started with NRF51822 and BLE in general; I have built a simple prototype with the BLE Nano using Arduino+BLEPeripheral library. I have converted that...
Hello,
I've read that some devices (e.g. Nexus 4 and Nexus 7) notify only about the first adv. packets from connectible peripheral and the only solution is to disable continuous...
Hello
I am working on a proprietary radio protocol while dealing with a problem that I stuck at for 2 days now. I am managing to get the radio stuck in a TX state (NRF_RADIO...
Hi,
I would like to ask a question about the power consumption specified in nRF8001 datasheet:
the graph on page 40 shows that the average current consumption is about ...
uart not accepting my static passkey when i added dfu in my project. using ios app nrftoolbox.
programed soft device s110. programed dfu dual bank example project then uploaded...
hi i am trying to setup a connection with CP2130 with nrf51. i am using nrf6310 kit. i flashed the spi slave example into into nrf51. on nrf51 these are the connection pins...
