Hi,
I'm developing custom firmware on the appcore and netcore. The netcore runs BLE controller, as well another custom IPC service to communicate between the appcore and...
Hi everyone,
I’m working on a project involving the nRF7002DK, where I’m trying to combine two separately working applications:
A TinyML CIFAR-10 image classification...
Hi,
we are looking into incorporating a NRF52 module into our control units, but to allow extending the antenna position away from the case through male-female SMA cables...
I opened up the nRF Connect for Desktop application and noticed a new version for the SDK , 3.0.0. I also noticed that the application is being deprecated.
Inside of Visual...
Hi,
I am trying to use nfc_t4t_lib and I have some issues because processing incoming data takes some time (around 100 ms) and therefore sending the response occurs late...
Hello Everyone,
I try to develop Nuvoton + NRF24L01 SPI communicate each other. And I don't understand why MISO bus has 0x0E after I send Write_Command 0x20?
void NRF24_AdressTX...
I'm working on a design that requires an adc reading to be taken on a pin that is also used as an interrupt. I've looked at the reference manual but am still confused as to...
The end of memory bss is @ 0x20002DAC (11692B).
The start of the heap is @ 0x20002DB0 with a size of 2560B.
The heap ends at 0x200037B0.
The stack works back from the end...
Hi,
I intend to buy the NRF51822 beacon to use it to transmit data from an SPI-linked sensor. Is this feasible? (It seems so, but I just want to make sure). Also, will I...
Yesterday was the nrf Beacon application for Andriod Studio released. I added the project DFU library to the same folder as described. But I get an error:
Gradle 'Android...
Hello! I want to try IPV6 for nrf51822. I have a few questions:
How many connections can be provided by the one device?
Can we broadcast messages between devices...
Hi,
I'm developing BLE functions using nRF51822 on top of the Android Kitkat applied device. I cannot find android bluetooth HAL source code that Nordic provides. Is there...
In my application I have a custom board with a single LED. While advertising the LED blinks at 1Hz and when connected the LED goes solid. However while testing with a proven...
I'm creating an application based on the s110 SoftDevice found in nRF51_SDK_8.0.0_5fc2c3a. I'm new to the SoftDevice framework so I've probably made an error somewhere but...
Is the GPIO pull down/up asserted on the 'inside' of the input disconnect switch or at the input/output pad? The diagrams would indicated that it is on the 'inside' of the...
This is function definition:
static uint32_t battery_level_char_add(ble_bas_t * p_bas, const ble_bas_init_t * p_bas_init)
This is declaration of the automatic variable...
Before starting advertising, we want to write some configuration information to NVM. In order to write to NVM, we first call sd_flash_page_erase and wait for the response...
I just posted a package of simple tools I wrote for OSX over on Sourceforge . The main app is a Cocoa app which lets you choose code, softdevice and bootloader (last two optional...
I Saw iBeacon Packet in the website
(d6 be 89 8e) Access Address for Advertising
(40 24) Header
(05 a2 17 6e 3d 71) Mac address
(02 01 1a 1a ff 4c 00 02 15 e2 c5 6d...
I want my peripheral device to act as a beacon while it is in a connected state with a master device. Is it possible to start not-connectable advertising in parallel with...
I am working on a nrf51822 UART bootloader using Keil 5.14 (though I had the same problem with 5.1). If I start with the pack example dfu_dual_bank_serial_s110_pca10028 with...
