Hello,
I just downloaded nRF connect for Desktop App, and plugged in PCA 10100 2. 0. 0 , 2023, 3.
I ran quick start, and this is what I get.
Any explanation on why...
Hi Nordic Team,
I have developed a couple applications for the nRF52833 using Zephyr and have now moved to the nRF54l15. For this new application, power consumption is...
Hi,
I have question about a project I'm running on nRF connect sdk 2.9.1.
I noticed that whenever an i2c sensor device device_init() is returning a value not equal...
I am trying to run some of the more basic examples included in the nRF Connect SDK on the nRF5340 included in a Thingy:91 X . I have installed the latest version of the nRF...
The OSCILLATORS documentation says:
" The device starts at 64 MHz. For 128 MHz, it must be configured when the CPU starts and before any peripherals that use the high-frequency...
Hello,
I am using nRF54l15 and nRF Connect SDK v2.9.0
I need to know if there is any way to disable the cfg_changed callback at runtime. I want it to be called in case...
I am in the process of getting a Nordic Thingy 91 X up and running for an upcoming development project. However, I’m having some problems getting the Thingy to connect to...
We are developing an app that communicates with a custom LCD display via IIC (TWI in Nordic terms) so it needs to send a lot of data on the IIC bus. We have developed an interrupt...
Hi all, help me please.
I am using two NRF24L01 (green color)
1 NRF24L01 is connected with Arduino mega 2560
another one is connected with arduino ADK
I was trying to...
I'm using an nRF8001 with a local GATT service and characteristic with Indications.
This corresponds to figure 29 in the Product Specification.
When the peer sends a Confirmation...
I was able to add Manufacturer Specific Data to the advertising packet on the nRF51822 without any problems, but I don't see any straight-forward way to do this on the nRF8001...
Hi,I am using nrf51822,I want to know more about address0 address1,prefix and adderss match,where
can I find more detailed document exept <<nRF51_Reference_manual v1.1>>
I am just starting with NRF51822 (can't even program the BLE example as IAR support is inadequate but that's another story) and trying to figure out power requirements for...
Just wondering,
What if I configure the Tx power level or some other attribute. What do I have to do to save the value to be used when the unit restarts?
Hello all,
I would like to ask you something,
I've done all my development with NRF24L01+ but now I have some NRF24L01 modules.
I know that NRF24L01+ is fully compatible...
Hi
I am created one more timer in ble_app_hrs
like in timer_init()
err_code = app_timer_create(&m_current_timer_id,
APP_TIMER_MODE_REPEATED,
current_timel_meas_timeout_handler...
I'm a little lost on the GPIO mappings from the code to the outside world. I'm playing with the UART example on the nRF6310 board. In the sample code, IO 16 is RX and IO 17...
Hi,
I am using ble_app_hrs application as a reference code.
in our case i have gpio interrupt for every 25 ms.
what should i keep BUTTON_DETECTION_DELAY for 25ms...
Does the lcd clobber the tmr0 and/or ANT ???
We just went through several days of working w/ ns on running ANT w/ RTC with a resolution of using sd_ calls.
Is the LCD...
Hi,
i am using nrf51822 custom board.
For our application i am using ble_app_hrs source code.
in that i have gpio interrupt for every 500ms, to get data from accelerometer...
For example, if I have a GPIO pin configured with low sense, and it goes low just before I call sd_power_system_off(), will the device return to System ON mode immediately...
