I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hello,
From the datasheet of nRF52840, I found the 32MHz crystal's package is 2016 (reference circuit).
Is it necessary? Can I use bigger package?
Thank you.
Hello, I am trying to create a clone of a temperature sensor with the nRF52840 DK. I catched all important data from the sensor to configure the nRF52840 DK. But I cant find...
Hello.
I am trying to implement a Zigbee Network were sensors will be posting data periodically to a Coordinator.
I was looking into the examples provided with the SDK...
Hi team,
Our customer use nRF52810 to be an RF dongle.
They meet an question was about the high PER when there was an headset dongle was near nRF52810 as bellowing....
Hi,
I had the issuse about power consumption of saadc.The current measured was always more than 500ua after I called nrfx_saadc_sample().My test code is below.
I am using nRF32 ble module. I am not able to get the value from BluetoothGattCharacteristic. I have declared an object of BluetoothGattCharacteristic and getting the value...
Hi everyone,
SDK version: 15.3.0
I read the DFU documentation and can't find the <InstallFolder>\examples\dfu\bootloader_secure_ble folder in SDK 15.0.3.
This folder...
Hi.
I have problem with dfu over ble with mesh sdk. I use example experimental_lpn as guide. When I add this dfu functionality in my project, my application is not responding...
We are designing a radio transmitter for a long range hobby craft vehicle with Gazell. We need to use frequency hopping as well as the pairing functionality that Gazell offers...
Hi,
I have few questions to be cleared before get into the nRF9160 to use in India.
As per the datasheet, nRF9160 supports LTE CAT M1 and NB1/NB2.
Can I be able to use...
For Above case i am planning to interface with U FL to SMA cable for external antenna interface. nrf9160 ant pin and U FL connector will be routed using 50 E impedance. at...
Hi,
I have found an interesting behavior from this code:
nrf_gpio_cfg_input(7,NRF_GPIO_PIN_NOPULL);
if (nrf_gpio_pin_read(7)==0)
{
NRF_LOG_INFO("ID1(P0.%d) is LOW...
Hi,
I am developing the proprietary protocol by using ESB function in nRF52832.
If the linear distance between the two devices is less than 10 cm, normal communication...
Hey! I am very new to the NRF52 environment, and have just started tinkering with the BLE capabilities. For my project I need to send 5 Kbytes of sensor data as fast as possible...
Hey.
We use the same SPI bus for accessing an external flash memory and gyroscope device (Bosch chip).
We encounter a problem regarding the SPI when performing the...
