We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi everyone,
I’m working with a Zephyr input overlay where I define double-tap , longpress , and extra_longpress behaviors on the same physical button.
This is the overlay...
I am updating my ncs from ncs2.7.0 to 2.9.2. I have a dfu application for which the build targer is nrf52840 and nrf5340. For this reason, I have pm_static files. for some...
I am using SDK version v3.2.1 and trying to put the nRF54L15 DK board into deep sleep using the sys_poweroff () function and wake it up using Button 1 on the DK.
This setup...
I get this error when i try to use FATFS or LittleFS - RAM works though /Users/admin/mass_1/src/main.c: In function 'setup_flash': /opt/nordic/ncs/v2.9.0/nrf/include/flash_map_pm...
Looks like Gazell can't run on nrf52810 with nrf5 SDK :
I don't knnow whether it is possible to create app on it with nrf connect SDK.
I think nrf connect SDK will need...
Hi, I have purchase a circuitdojo_feather_nrf9151 board it has LIS2DH12 and npm1300 on i2c2 i also want to connect SHT40 but facing issue this sensor is not detecting on i2c...
Hey all, I wanted to enable shutdown and standby modes for this chip, but realised that I can not use the layer of zephyr. When i try to CONFIG_PM=y in prj.conf it does not...
Hi,
I'm running the system_off/ sample on v3.2.3 with these settings in prj.conf
And with this overlay file:
However, I can see that there's a high (and in fact...
Hello, I'm building a multi-image project for an nRF9151: a two-stage bootloader (NSIB + MCUboot) plus two independent non-secure app images.
Each app needs to be able to...
I'm using the MCUmgr + MCUboot solution for BLE OTA FW updates (i.e. CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU).
Is there any way to require pairing for firmware updates? I see...
I'm trying to capture a ble connection with nrfutil. What I've done:
- installed nrfutil on my arch based linux machine
- install ble-sniffer
- setup the nRF52840 Dongle...
I am aware from this post https://devzone.nordicsemi.com/f/nordic-q-a/106424/ble-audio-test-app-supporting-both-cis-and-bis t hat the primary LE Audio controller does not...
Hello, I have a wierd bug on my board using an nrf54l10. I am using the sys_poweroff(), function to put my device to sleep. Everything is working fine. However, sometimes...
