i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
I am working on BLE development and need to study the BLE heart rate collector and peripheral examples. I plan to flash ble_app_hrs onto nRF51422 and ble_app_hrs_c onto nRF52840...
I am using nRF52832 SDK 15.3 and type 4 tag and some phones like iPhone 11 and Samsung S20+ are not able to detect the tag. The tag works with other phones so I don't think...
Hi there,
I'm using nrf52840 DK and Custom board, SDK 17.0.2, Segger Embedded Studio(SES v5.20)
my issue is when I receive data from UART interrupt based on serial uartes...
I'm developing a system of nRF9160, nRF52832 and Iridium 9603 (satellite modem) - all on the same main board. The nRF9160 is the brain of the system and handles LTE, GPS and...
Hi,
I am new to working with nrf52840 devices. I am wondering if it is possible to change the transmission power of packet during transmission several times such that some...
I wanted to increase the bandwidth of bluetooth using the following example, but there is a limit of only 1 board.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17...
project : zephyr
controller stack : zephyr stack
description ： we start direct adv using our DK，and we want it send broadcast only once。 but zephyr stack send adv all...
Hi,
I am working on NRF52 series (NRF52 DK and NRF52832) and would like to know whether it is possible to use Bluetooth 5 extended advertising capabilities to send, let...
Hi there, I'm routing the nrf9160 to a STM32 and I need to know the pinout for COM port used.
On my PC, I know COM11 is the one that is used for AT Commands
But, I...
Hi,
I'm using NRF52840 with direct test mode application.
I'm sending to the function dtm_cmd following parameters: 0x4000, 0x8000, 0x9400, 0xA500.
I understand...
Hi,
After suspending task in a specific code line (using vTaskSuspend) and resuming the task (using vTaskResume)- will the task continue from the specific suspension line...
I am going to make a project with nRF52840 In my application, I need to send sensor data to Raspberry Pi I noticed this tutorial and tried to implement this in my project...
i tried to implement radio notification in order to change advertising data but i had this error
when i put the periority to LOW i get this error, if put MID or HIGH the...
What benefit is there to RX gain for the bluetooth front end module
Most other 2.4 amplifiers do not have RX gain.
Our concern is the noise floor, would not the RX gain...
