We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hello,
I am trying to send a single adv packet when a certain condition in the application is met. To do this I am calling ADV_start for the initial adv packet and then...
These questions are in the context of using an nRF52840 in a serialization application. But I don't believe this will impact the information I am trying to understand. The...
I want to program the firmware into a nrf52840 on our custom board to be the NCP and do the DFU over thread. I can not use the DK board and have the nrfutil load the firmware...
Hi,
Our application uses MQTT over TLS to talk to a MQTT broker.
The MQTT APIs used are like in the 'mqtt_simple' sample code.
When mqtt_connect is called with invalid...
Hi,
I'm designing an application using SEGGER Studio for the nRF52832. I have based my application on the template peripheral example.
What I want to do is to trigger...
Hi--
I tried to implement an internally managed RTC using the app timer library, but came to find the error on that is too much for an RTC (~25 min lost over a few days...
I want to know which pins serve the purpose of TX and RX in nRF51822. I suspect its the ANT1 and ANT2 but i want to confirm and also if the following would be a good way to...
I just buy nrf52840 Dongle.
I connect nrf52840 Dongle to my USB port and open nrf Connect.
I look at guide https://devzone.nordicsemi.com/nordic/short-range-guides/b/getting...
Im using sdk 15.2 with 2 nrf52840 boards, i would like the server to connect to a particular client. How to add the devices to whitelist in sdk 15.2 ?. I have gone through...
Hello,
I am working on a scanner code, I have initialize my scanner with this parameters.
and in nrf_ble_scan_init()
It is getting reset once in the beginning like...
Hi,
without any obvious reason one of our nRF52840 DKs stopped being visible over the USB (J2) interface. The nRF52840 is still functional and can be programmed from another...
Hi. I'm using nRF52832, SDK13.0.0, S132.
First of all, I already know this Q has lots of Q and A.
But I'm so confused which case do I pick.
In my case, iPhone has...
I am a student studying zigbee. We succeeded in turning on/off the LEDs of zc_light using examples of zc_light and zc_switch. The question here is, where do you send and receive...
I am trying to duplicate a RF remote control which uses a Nrf24L01+ IC.
I have temporarily connect the SPI interface of my test chip to the SPI pins on the remote, and transmitted...
