Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
My nrf51 DK Board is not detected by Keil as jlink probe, but with other tools. As a result I am unable to download demo projects to my board.
unmodified nrf51 dk has...
I'm working in SDK 14.2, and trying to send a single byte over SPI between two NRF5 boards using the SPI peripheral examples (1 master and 1 slave). However, SPI always seems...
Hello!
There are no hex files that are pre-made for the ble_app_interactive example. When I use VMware to run a Linux environment on Ubuntu to get an executable with gcc...
Hello,
I want to configure my nRF52840 development kit for counting input pulses on one of the GPIOs (Pin 13) in this case. I am using SEGGER Embedded Studio as IDE.
Here...
Hello,
we have a strange proglem with nrf52811 on an own board
after uart initialization and connecting the scope (Saleae) probe to the RX pin the device outputs fatal...
Hi,
I have a ARM core device like raspberry pi / orange pi etc, where I run a build and deploy server - basically compiling code and flashing to a target.
I have the...
We are trying to use serial port library for simple UART comms in IRQ mode at 115200, but experiencing what looks like stuck TX interrupt. PCA10040 with SDK 15.3.
In the...
I'm using nRF Connect v3.0.0 to run Getting Started Assistant v0.9.3 and get a message it is only compatible with 2.4.0 (very old). I can install and verify Tool Chain except...
Hi
I am trying to connect and bond a nrf52832 to Galaxy S6, Android 7.0 by OOB / NFC with the ble_nfc_pairing_reference_pca10040_s132 example.
I selected LE Secure Connections...
Hi nordic,we want to config nrf52832 as a wireless full-duplex serial port transmission module through nordic proprietary protocol，so the module can send and receive data...
I have my IMEI but my pin number has 4 digits: 0000, instead of 6 digits(which is required to add the LTE device)? Please Nordic, what should I do? I have this problem for...
Hello,
I have problems setting the output RF power to +8 dBm during DTM test using the example dtm application. The example dtm application is used as it is provided with...
Hello,
i've been searching the forum for answers about Bluetooth certification but i'm very confused.
I want to use nRF52832 in my project, and i would like to make make...
I am trying to transferAdvertisement data from NRF52832 to Raspberry PI using BLE_app_UART example. I have updated the config as below,
app_uart_comm_params_t const comm_params...
