I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi all,
I am working with a BNO080 imu and have ported an Adafruit library into the ble_app_template and created a custom service.
Independently, the IMU code and the...
Dear Nordic,
I am running into an interesting side effect when I disable the app scheduler library from my program. I have been previously using the app scheduler to service...
Hi,
1/ Is it mandatory for Direction Finding process to have all streaming advertising messages from beacon to locator connectable ?
2/ Is it possible/easy to manage live...
Hi,
I have an application and I want to send the output of the application via CoAP LTE connection. My plan is to modify the nrf-sdk CoAP Client sample to achieve this...
We are trying to use mcumgr/mcuboot with Zephyr on nRF53. During development, we have enabled the Zephyr shell functionality and would like to use mcumgr with it (CONFIG_MCUMGR_SMP_SHELL...
Hello!
I've got a problem when performing a DFU OTA. I first flash my software(#1) with bootloader in de nrf53840DK. When i make changes to the software i use app_update...
Good day, I have seen a few people asking about connecting the Nordic devices with the RFM95/Sx1276 modules. I understand that it is SPI driven, but I am a complete novice...
Hi,
I'm using nrf52840 to connect a mobile device via BLE.
I've noticed that when a lot of messages are sent, a disconnection occurs with reason code of NRF_ERROR_RESOURCES...
Hi there!
I'm currently facing an issue where the client will stop transmitting messages after six hours and twenty-five minutes. This is the case after 255 messages have...
Hi everybody.
I'm margin two different projects:
examples\peripheral\usbd_hid_generic
with
examples\ble_peripheral\ble_app_hids_keyboard
but, using the make file...
Hi,
I am using a custom board that uses Arm Cortex-A7 and embedding an nRF52840, There is no external low-frequency crystal 32kHz connected to the nrf52 chip, so I've enabled...
Hi ,
I'm trying to use http_application_update , on an https website, and i get:
I: Attempting to connect over IPv4 I: Setting up TLS credentials E: Unable to connect...
Hi,
I want to transmit data on each button ( lets say 4 buttons for now ) press on my custom board. I have used ble_app_beacon example and tutorial https://devzone.nordicsemi...
Hello
I have uploaded USB CDC ACM example code in my custom board of nRF52840. I didn't get Vcc on D+ pin and cannot detect USB. I have also check soldering side and resistance...
