Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hello
I am at the early stage of evaluation of a nRF52840 USB Dongle and I have installed all software on my Win 11 PC.
Just trying to check that everything is working...
We have made 2 partition of Internal flash. One is for running Application and Other for storing some configuration. I am trying to erase the page of 2nd partition, and it...
Hi,
I have been performing a fresh install of the toolchain following the nordic's "nRF Connect for VS Code" page, as well as the YouTube video "Introducing nRF Connect...
Hello,
Developing a custom board with nRF9160 as application CPU and nRF52810 as BLE Controller. Connected via SPI + reset + irq lines to the 52810. The design is a copy...
This might be a simple one to answer but I'm struggling to find documentation on what to do here since we're still using an ancient SDK on 9160.
I have a working board file...
Hello,
We have a BLE connection issue. We want to connect a Windows 11 laptop with a nrf5340 eval board.
The connection procedure can fail by a disconnection with reason...
I have a custom PCBA with which has the flow of:
- Boot
- Advertise some temperature data read from TWI with a 5 second timeout using `ble_adv_fast_timeout`.
- I then...
I want to implement secure connections for a device based on the nRF52832, protected by a PIN/pass key, which I need to be able to configure dynamically, not hardcoded in...
Hi there
I am struggeling to find a solution to automatically connect to the controller when found based on the advertised name. I do not want to click on the found device...
Hello,
I am developing project on ESP32, with nPM1300. I am interested in battery state/capacity measurement provided by the Fuel Gauge example. Some part of the algorithm...
Hello. I followed the steps in the video to develop a project on my custom board.
www.youtube.com/watch
I created a new board and new application (blinky sample). Then...
I encounter problems moving to VScode + nRF Connect extension. Even the simplest step creates countless problems. I followed the official NRF tutorial on youtube and nothing...
Hi, in the development kit of nRF52840, the oscillator for the micro is configured as follow
In the bom, it can be seen that the used oscillator is the MP06003 that correspond...
To advertise a *configurable* device name the previous guidance seemed to be:
prj.conf
Code Snippet
Please note I have intentionally removed all error handling...
Hello,
I have multiple UART devices connected to various pins on my nRF5340, but due to hardware limitations, I can only use two UARTs concurrently alongside interfaces...
